Danfoss VLT HVAC Скачать руководство пользователя страница 30

Страница: 30 / 99

3.3 Main Menu - Brakes - Group 2

2-00 DC Hold/Motor Preheat Current

Range:

Function:

50.0 %

[0.0 -
160.0 %]

Set holding current as a percentage of the
rated motor current IM,N

1-24 Motor Current

2-00 DC Hold/Motor Preheat Current

holds the

motor function (holding torque) or pre-heats
the motor. This parameter is active if DC
hold is selected in

1-72 Start Function

[0] or

1-80 Function at Stop

[1].

NOTE

The maximum value depends on the rated motor current.
Avoid 100% current for too long. It may damage the motor.

2-01 DC Brake Current

Range:

Function:

50.0 %

[0.0 - 150.0
%]

Set current as % of rated motor current,

1-24 Motor Current

. DC brake current is

applied on stop command, when speed is
below the limit set in

2-04 DC Brake Cut In

Speed

; when the DC Brake Inverse function

is active; or via the serial port. See

2-02 DC

Braking Time

for duration.

50.0 %

[0.0 - 150.0
%]

NOTE

The maximum value depends on the rated motor current.
Avoid 100% current for too long. It may damage the motor.

2-02 DC Braking Time

Range:

Function:

10.0 s

[0.0 - 60.0 s] Set the duration of the DC braking current

set in

2-01 DC Brake Current

, once activated.

2-04 DC Brake Cut In Speed

Range:

Function:

0.0 Hz

[0.0 - 400.0
Hz]

This parameter is for setting the DC brake
cut in speed at which the DC braking
current

2-01 DC Brake Current

is to be

active, in connection with a stop
command.

3.3.1 2-1* Overvoltage Control

Par. group for selecting dynamic braking parameters.

2-10 Brake Function

Option:

Function:

[0]

Off

No brake resistor installed.

2-17 Over-voltage Control

Option:

Function:

Select whether to enable OVC, which reduces the
risk of drive trip due to over voltage on the DC link
caused by generative power from load.

[0]

Disabled No OVC required.

[2]

Enabled Activates OVC.

NOTE

The ramp time is automatically adjusted to avoid tripping of
the frequency converter.

Parameters

VLT HVAC Basic Drive Programming Guide

MG.18.B1.02 - VLT

is a registered Danfoss trademark

Содержание VLT HVAC




































































































Результаты поиска

Содержание VLT HVAC

Отзывы:

Бренды по названию

Популярные бренды

Danfoss VLT HVAC, Руководство по программированию

Результаты поиска

Содержание VLT HVAC

Отзывы:

Бренды по названию

Популярные бренды