Danfoss VLT HVAC Скачать руководство пользователя страница 32

Страница: 32 / 85

If acceleration problems were encountered

•

If warnings or alarms occur, see

8 Warnings and

Alarms

•

Check that motor data is entered correctly.

•

Increase the ramp-up time in

3-41 Ramp 1 Ramp

Up Time

•

Increase current limit in

4-18 Current Limit

•

Increase torque limit in

4-16 Torque Limit Motor

Mode

If deceleration problems were encountered

•

If warnings or alarms occur, see

8 Warnings and

Alarms

•

Check that motor data is entered correctly.

•

Increase the ramp-down time in

3-42 Ramp 1

Ramp Down Time

•

Enable overvoltage control in

2-17 Over-voltage

Control

NOTE

The OVC algorithm does not work when using PM motors.

See

8.4 Warning and Alarm Definitions

for resetting the

frequency converter after a trip.

NOTE

3.1 Pre-start

through

3.7 Local-control Test

in this chapter

concludes the procedures for applying power to the
frequency converter, basic programming, set-up, and
functional testing.

3.8 System Start Up

The procedure in this section requires user-wiring and
application programming to be completed.

6 Application

Set-Up Examples

is intended to help with this task. Other

aids to application set-up are listed in

1.2 Additional

Resources

. The following procedure is recommended after

application set-up by the user is completed.

CAUTION

MOTOR START!

Ensure that the motor, system, and any attached
equipment is ready for start. It is the responsibility of the
user to ensure safe operation under any condition. Failure
to do so could result in personal injury or equipment
damage.

Press [Auto On].

Ensure that external control functions are
properly wired to the frequency converter and all
programming is completed.

Apply an external run command.

Adjust the speed reference throughout the speed
range.

Remove the external run command.

Note any problems.

If warnings or alarms occur, see

8 Warnings and Alarms

3.9 Acoustic Noise or Vibration

If the motor or the equipment driven by the motor - e.g. a
fan blade - is making noise or vibrations at certain
frequencies, try the following:

•

Speed Bypass, parameter group 4-6*

•

Over-modulation,

14-03 Overmodulation

set to off

•

Switching pattern and switching frequency
parameter group 14-0*

•

Resonance Dampening,

1-64 Resonance

Dampening

Start Up and Functional Tes...

VLT

HVAC Drive Operating Instructions

MG11AH02 - VLT

is a registered Danfoss trademark

Содержание VLT HVAC






















































































Результаты поиска

Содержание VLT HVAC

Отзывы:

Похожие инструкции для VLT HVAC

Бренды по названию

Популярные бренды

Danfoss VLT HVAC, Руководство по эксплуатации

Результаты поиска

Содержание VLT HVAC

Отзывы:

Похожие инструкции для VLT HVAC

Бренды по названию

Популярные бренды