Danfoss VLT FCD 303 Скачать руководство пользователя страница 77

Страница: 77 / 127

VLT

FCD Series

Programming, FCD

300

■

Serial communication for FCD 300

■

Protocols

All frequency converters are equipped with an RS 485

port as standard, which makes it possible to choose

between two protocols. The two protocols that can

be selected in parameter 512

Telegram Profile

, are:

•

Profidrive protocol

•

Danfoss FC protocol

To select Danfoss FC protocol, parameter 512

Telegram Profile

is set to

FC protocol

[1].

■

Telegram Traffic

Control and response telegrams

Telegram traffic in a master-slave system is controlled

by the master. A maximum of 31 slaves can

be connected to a master, unless repeaters are

used. If repeaters are used, a maximum of 126

slaves can be connected to a master.

The master constantly sends telegrams addressed to

the slaves and waits for response telegrams from them.

The slave

’

s response time is a maximum of 50 ms.

Only a slave that has received an error-free telegram,

addressed to that slave can send a response telegram.

Broadcast

A master can send the same telegram simultaneously

to all slaves connected to the bus. During this

broadcast communication the slave does not send

any response telegrams back to the master as to

whether the telegram has been correctly received.

Broadcast communication is set up in address

format (ADR), see

Telegram structure

Content of a character (byte)

Each character transferred begins with a start bit.

Then 8 data bits are transferred, corresponding to

a byte. Each character is secured via a parity bit,

which is set at "1" when it reaches parity (i.e. when

there is an equal number of 1

’

s in the 8 data bits

and the parity bit in total). A character is completed

by a stop bit, thus consisting of 11 bits in all.

■

Telegram Structure

Each telegram begins with a start character (STX)

= 02 Hex, followed by a byte that denotes the

length of the telegram (LGE) and a byte that denotes

the address of the frequency converter (ADR).

Then follows a number of data bytes (variable,

depending on the type of telegram). The telegram

is completed by a data control byte (BCC).

Telegram timing

The communication speed between a master and

a slave depends on the baud rate. The frequency

converter

’

s baud rate must be the same as the master

’

baud rate and be selected in parameter 501

Baudrate

After a response telegram from the slave, there

must be a pause of at least 2 characters (22 bits)

before the master can send a new telegram. At a

baud rate of 9600 baud there must be a pause of

at least 2.3 ms. When the master has completed

the telegram, the slave

’

s response time back to the

master will be a maximum of 20 ms, and there

will be pause of at least 2 characters.

Pause time, min: 2 characters

Response time, min: 2 characters

Response time, max: 20 ms

The time between the individual characters in a

telegram may not exceed 2 characters and the

telegram must be completed within 1.5 x nominal

telegram time. At a baud rate of 9600 baud

and a telegram length of 16 bytes the telegram

will be completed after 27.5 msec.

MG.04.B7.02 - VLT is a registered Danfoss trademark

Содержание VLT FCD 303
































































































































Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды

Danfoss VLT FCD 303, Руководство по эксплуатации

Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды