8-56 Preset Reference Select
Option:
Function:
[0]
Digital
input
Activates preset reference selection via a digital
input.
[1]
Bus
Activates preset reference selection via the
serial communication port or fieldbus option.
[2]
Logic AND Activates preset reference selection via the
fieldbus/serial communication port and via 1 of
the digital inputs.
[3]
*
Logic OR
Activates the preset reference selection via the
fieldbus/serial communication port or via 1 of
the digital inputs.
8-90 Bus Jog 1 Speed
Range:
Function:
100 RPM
*
[ 0 - par. 4-13
RPM]
Enter the jog speed. Activate this
fixed jog speed via the serial port
or fieldbus option.
8-91 Bus Jog 2 Speed
Range:
Function:
200 RPM
*
[ 0 - par. 4-13
RPM]
Enter the jog speed. Activate this
fixed jog speed via the serial port
or fieldbus option.
10-00 CAN Protocol
Option:
Function:
NOTICE
The options depend on the installed
option.
[0] CANopen
[1] DeviceNet View the active CAN protocol.
10-01 Baud Rate Select
Select the fieldbus transmission speed. The selection must
correspond to the transmission speed of the master and the
other fieldbus nodes.
Option:
Function:
[16]
10 Kbps
[17]
20 Kbps
[18]
50 Kbps
[19]
100 Kbps
[20]
125 Kbps
[21]
250 Kbps
[22]
500 Kbps
10-02 MAC ID
Range:
Function:
Size related
*
[ 0 - 63 ] Selection of station address. Every
station connected to the same
DeviceNet network must have an
unambiguous address.
10-05 Readout Transmit Error Counter
Range:
Function:
0
*
[0 - 255 ] View the number of CAN control transmission
errors since the last power-up.
10-06 Readout Receive Error Counter
Range:
Function:
0
*
[0 - 255 ] View the number of CAN control receipt errors
since the last power-up.
10-07 Readout Bus Off Counter
Range:
Function:
0
*
[0 - 255 ] View the number of fieldbus off events since the
last power-up.
10-10 Process Data Type Selection
Option:
Function:
Select the instance (telegram) for data
transmission. The instances available depend
on the setting of
parameter 8-10 Control
Profile
.
When
parameter 8-10 Control Profile
is set to
[0] FC profile
,
options
[0] INSTANCE 100/150
and
[1] INSTANCE 101/151
are available.
When
parameter 8-10 Control Profile
is set to
[5] ODVA
,
parameter 10-10 Process Data Type
options
[2] INSTANCE 20/70
and
[3]
INSTANCE 21/71
are available.
Instances 100/150 and 101/151 are Danfoss-
specific. Instances 20/70 and 21/71 are ODVA-
specific AC motor profiles.
For guidelines in telegram selection, refer to
the
VLT
®
DeviceNet MCA 104 Installation Guide
.
NOTICE
A change to this parameter is executed
immediately.
[0] INSTANCE
100/150
[1] INSTANCE
101/151
[2] INSTANCE
20/70
[3] INSTANCE
21/71
10-11 Process Data Config Write
Select the process write data for I/O assembly instances 101/151.
Elements [2] and [3] of this array can be selected. Elements [0]
and [1] of the array are fixed.
Option:
Function:
[0]
None
[302]
Minimum Reference
Parameters
VLT
®
DeviceNet MCA 104
32
Danfoss A/S © 12/2015 All rights reserved.
MG92F102
6
6
Содержание VLT DeviceNet MCA 104
Страница 2: ......
Страница 49: ...Index Programming Guide MG92F102 Danfoss A S 12 2015 All rights reserved 47...