Danfoss VLT CANopen MCA 105 Скачать руководство пользователя страница 33

Страница: 33 / 50

8-17 Configurable Alarm and Warningword

The configurable alarm and warning word has 16 bits (0-15).
Each of those bits can be configured to any of the following
options.

Option:

Function:

[8]

DC undervoltage warning

[9]

Inverter overloaded warning

[10]

Motor ETR overtemp warning

[11]

Motor thermistor overtemp warning

[12]

Torque limit warning

[13]

Over current warning

[14]

Earth fault warning

[17]

Controlword timeout warning

[19]

Discharge temp high warning

[22]

Hoist mech brake warning

[23]

Internal fans warning

[24]

External fans warning

[25]

Brake resistor short circuit warning

[26]

Brake powerlimit warning

[27]

Brake chopper short circuit warning

[28]

Brake check warning

[29]

Heatsink temperature warning

[30]

Motor phase U warning

[31]

Motor phase V warning

[32]

Motor phase W warning

[34]

Fieldbus communication warning

[36]

Mains failure warning

[40]

T27 overload warning

[41]

T29 overload warning

[45]

Earth fault 2 warning

[47]

24V supply low warning

[58]

AMA internal fault warning

[59]

Current limit warning

[60]

External interlock warning

[61]

Feedback error warning

[62]

Frequency max warning

[64]

Voltage limit warning

[65]

Controlboard overtemp warning

[66]

Heatsink temp low warning

[68]

Safe stop warning

[73]

Safe stop autorestart warning

[76]

Power unit setup warning

[77]

Reduced powermode warning

[78]

Tracking error warning

[89]

Mech brake sliding warning

[163]

ATEX ETR cur limit warning

[165]

ATEX ETR freq limit warning

[10002]

Live zero error alarm

[10004]

Mains phase loss alarm

[10007]

DC overvoltage alarm

[10008]

DC undervoltage alarm

[10009]

Inverter overload alarm

[10010]

ETR overtemperature alarm

[10011]

Thermistor overtemp alarm

8-17 Configurable Alarm and Warningword

The configurable alarm and warning word has 16 bits (0-15).
Each of those bits can be configured to any of the following
options.

Option:

Function:

[10012]

Torque limit alarm

[10013]

Overcurrent alarm

[10014]

Earth fault alarm

[10016]

Short circuit alarm

[10017]

CTW timeout alarm

[10022]

Hoist brake alarm

[10026]

Brake powerlimit alarm

[10027]

Brakechopper shortcircuit alarm

[10028]

Brake check alarm

[10029]

Heatsink temp alarm

[10030]

Phase U missing alarm

[10031]

Phase V missing alarm

[10032]

Phase W missing alarm

[10033]

Inrush fault alarm

[10034]

Fieldbus com faul alarm

[10036]

Mains failure alarm

[10037]

Phase imbalance alarm

[10038]

Internal fault

[10039]

Heatsink sensor alarm

[10045]

Earth fault 2 alarm

[10046]

Powercard supply alarm

[10047]

24V supply low alarm

[10048]

1.8V supply low alarm

[10049]

Speed limit alarm

[10060]

Ext interlock alarm

[10061]

Feedback error alarm

[10063]

Mech brake low alarm

[10065]

Controlboard overtemp alarm

[10067]

Option config changed alarm

[10068]

Safe stop alarm

[10069]

Powercard temp alarm

[10073]

Safestop auto restart alarm

[10074]

PTC thermistor alarm

[10075]

Illegal profile alarm

[10078]

Tracking error alarm

[10079]

Illegal PS config alarm

[10081]

CSIV corrupt alarm

[10082]

CSIV param error alarm

[10084]

No safety option alarm

[10090]

Feedback monitor alarm

[10091]

AI54 settings alarm

[10164]

ATEX ETR current lim alarm

[10166]

ATEX ETR freq limit alarm

Parameters

Programming Guide

MG92G102

Содержание VLT CANopen MCA 105


















































Результаты поиска

Содержание VLT CANopen MCA 105

Отзывы:

Бренды по названию

Популярные бренды

Danfoss VLT CANopen MCA 105, Руководство по программированию

Результаты поиска

Содержание VLT CANopen MCA 105

Отзывы:

Бренды по названию

Популярные бренды