Danfoss VLT 6000 HVAC Series Скачать руководство пользователя страница 25

Страница: 25 / 27

VLT

6000 HVAC

All about VLT 6000

HVAC

Automatic Motor Adaptation running (AMA RUN)

Automatic motor adaptation has been enabled in

parameter 107

Automatic Motor Adaptation, AMA.

Automatic Motor Adaptation completed
(AMA STOP)

Automatic motor adaptation has been completed.

The frequency converter is now ready for operation

after the

Reset

signal has been enabled. Please

note that the motor will start after the frequency

converter has received the

Reset

signal.

Stand by (STANDBY)

The frequency converter is able to start the motor

when a start command is received.

Stop (STOP)

The motor has been stopped via a stop

signal from a digital input, [OFF/STOP] button

or serial communication.

DC stop (DC STOP)

The DC brake in parameter 114-116 has been enabled.

DRIVE ready (UN. READY)

The frequency converter is ready for operation, but

terminal 27 is a logic "0" and/or a

Coasting command

has been received via the serial communication.

Not ready (NOT READY)

The frequency converter is not ready for operation,

because of a trip or because OFF1, OFF2

or OFF3 is a logic ‘0

’

Start disabled (START IN.)

This status will only be displayed if, in parameter

599

Statemachine, Profidrive

[1] has been selected

and OFF2 or OFF3 is a logic ‘0

’

Exceptions XXXX (EXCEPTIONS XXXX)

The microprocessor of the control card has stopped

and the frequency converter is out of operation.

The cause may be noise on the mains, motor

or control cables, leading to a stop of the

control card microprocessor.

Check for EMC-correct connection of these cables.

MG.60.C7.02 - VLT is a registered Danfoss trademark

Содержание VLT 6000 HVAC Series




























Результаты поиска

Содержание VLT 6000 HVAC Series

Отзывы:

Бренды по названию

Популярные бренды

Danfoss VLT 6000 HVAC Series, Быстрая настройка

Результаты поиска

Содержание VLT 6000 HVAC Series

Отзывы:

Бренды по названию

Популярные бренды