manualshive.com logo in svg

Danfoss VLT 2811, Быстрое руководство

Поделиться
Скачать
Danfoss VLT 2811 Скачать руководство пользователя страница 27

1.9.1 Warnings/alarm messages 

No.

Description

W A T

Cause of Problem

2

Live zero error (LIVE ZERO
ERROR)

X X X Voltage or current signal on terminals 53 or 60

is below 50% of preset value.

4

Mains phase loss (MAINS
PHASE LOSS)

X X X No phase on mains supply side.

5

Voltage warning high (DC
LINK VOLTAGE HIGH)

X     The intermediate circuit voltage exceeds the lim-

it set.

6

Voltage warning low (DC
LINK VOLTAGE LOW)

X     The intermediate circuit voltage is lower the limit

set.

7

Overvoltage (DC LINK
OVERVOLT)

X X X The intermediate voltage exceeds the limit set.

8

Undervoltage (DC LINK UN-
DERVOLT)

X X X The intermediate voltage is lower than the limit

set.

9

Inverter overload (INVER-
TER TIME)

X X   The frequency converter is close to tripping due

to overload.

10

Motor overloaded ( MOTOR,
TIME)

X X   The motor is too hot due to overload.

11

Motor thermistor (MOTOR
THERMISTOR)

X X   Either the motor is too hot or the thermistor has

been disconnected.

12

Current limit (CURRENT
LIMIT)

X X   Output current is higher than set in par. 221.

13

Overcurrent (OVERCUR-
RENT)

X X X The peak current limit has been exceeded.

14

Earth fault (EARTH FAULT)   X X Discharge from output phases to earth.

15

Switch mode fault (SWITCH
MODE FAULT)

 

X X Fault in switch mode power supply.

16

Short-circuit (CURR. SHORT
CIRCUIT)

 

X X Short-circuit on the motor terminals or in the

motor.

17

Serial communication time-
out (STD BUS TIMEOUT)

X X   No serial communication to the frequency con-

verter.

18

HPFB bus timeout (HPFB
TIMEOUT)

X X   No serial communication to the communication

option card.

33

Out of frequency range
(OUT FREQ RNG/ROT LIM)

X     Output frequency has reached the limit set in

either par. 201 or par. 202.

34

HPFB communication fault
(PROFIBUS OPT. FAULT)

X X   Fault only occurs in fieldbus versions. Please see

par. 953 in fieldbus literature.

35

Inrush fault (INRUSH
FAULT)

 

X X Connected to mains too many times within 1 mi-

nute.

36

Overtemperature (OVER-
TEMPERATURE)

X X   The upper temperature limit has been exceeded.

37-45 Internal fault (INTERNAL

FAULT)

 

X X Please contact Danfoss.

W:

 Warning, 

A:

 Alarm, 

T:

 Trip locked

1 Quick Guide

VLT 2800 Quick Guide

26

MG.28.M1.02 - VLT

®

 is a registered Danfoss trademark

1  

Содержание VLT 2811




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды