![background image](http://html1.mh-extra.com/html/danfoss/turbocor-tt-series/turbocor-tt-series_service-manual_4104524240.webp)
6. Remove the bearing sensor cable from the 9-pin feedthrough. Refer to Figure 4-265 Bearing Sensor
Feedthrough Removal (Rear (Left) Shown).
7. Using a hex socket, remove the four (4) M5x16 fasteners that secure the 9-pin feedthrough. Refer to
Refer to Figure 4-265 Bearing Sensor Feedthrough Removal (Rear (Left) Shown).
8. Carefully remove the 9-pin feedthrough. It may be necessary to use needle-nose pliers to grasp the
feedthrough. Do not pry the feedthrough out of the housing.
Figure 4-265 Bearing Sensor Feedthrough Removal (Rear (Left) Shown)
4.30.5.2 Bearing Sensor Feedthrough Installation
1. Using a lint-free cloth, clean the mating surface on the compressor housing.
2. Verify that the new O-rings and 9-pin feedthrough are clean. If not, wipe off any contaminants with a
lint-free cloth.
3. Apply O-lube on each of the new O-rings.
4. Install the new O-rings onto the new 9-pin feedthrough.
5. Install the new 9-pin feedthrough.
6. Secure the feedthrough with the four (4) M5x16 fasteners. Finger-tighten and then follow the torque
sequence shown in Figure 4-266 Bearing Sensor 9-Pin Feedthrough Connector Torque Sequence on
page 241 and torque to 3 Nm (2.2 ft.lb.). Torque the fasteners a final time to 5 Nm (3.7 ft.lb.).
Page 240 of 294 - M-SV-001-EN Rev. H 1/23/2023
Содержание Turbocor TT Series
