![background image](http://html.mh-extra.com/html/danfoss/tgh-series/tgh-series_applications-and-installation-manual_506646011.webp)
11 of 114
M-AP-001-EN Rev. Q
Chapter 1.0 Introduction
This Applications and Installation Manual is intended to be a guide for application data/installation
procedures specific to Danfoss Turbocor compressors. It is not intended to inform on fundamental
safety, refrigeration and electrical design skills. It is assumed and presumed that persons using this
manual are appropriately certified and have detailed knowledge, experience and skills in respect to
designing for and working with high pressure refrigerants and medium voltage electrical components
(to 1 KV high power AC & DC) as well as complex control systems.
Some potential safety situations may not be foreseen or covered in this guide. Danfoss LLC assumes
personnel using this manual and working on Danfoss LLC compressors are familiar with, and carry out
all safe work practices necessary to ensure safety for personnel and equipment.
1.1 Scope
This manual is designed for use with Bearing Motor compressor Controller (BMCC) software, Version
4.0.0 and later.
Table 1-1 Application Manual Applicability
1.2 Organization of this Manual
This Applications and Installation Manual is divided into the following sections:
1. Overview of the TTS/TGS series compressors - provides an overview of the Twin-Turbo and
Total-Green (TTS and TGS) series compressors, including an introduction to the compressor.
2. Compressor Module - provides details on the Compressor Module of the compressor, including
product capacity and application range, maximum pressure alarm, and fault limits.
3. System Design Guidelines - provides basic guidelines and requirements for the design and
manufacture of R134a, R513A, R515B, and R1234ze(E) systems equipped with Danfoss LLC TTS/
TGS series compressors.
4. Installation Guidelines - describes application/installation procedures specific to Danfoss
Turbocor TTS/TGS compressors.
1.3 Document Symbols
The following symbols are used in this document.
NOTE:
Indicates something to be noted by the reader.
NOTE
DANGER:
Indicates an essential operating or maintenance procedure, practice, or condition, which,
if not strictly observed, could result in serious injury to or death of personnel or long-term health
hazards.
Manual
Release Date
BMCC Firmware Versions
M-AP-001-XX Rev E
September 2013
CC 2.3.1213
M-AP-001-XX Rev L
October 2016
CC 3.1.4
M-AP-001-XX Rev M
November 2017
CC 4.0 and later
M-AP-001-XX Rev M.1
November 2017
CC 4.1 and later
M-AP-001-XX Rev N
May 2018
CC 4.1 and later
M-AP-001-XX Rev P.1
November 2019
CC 4.2 and later
THIS PAGE INTENTIONALLY LEFT BLANK
Содержание TGH Series
