background image

User Guide | Gas detecting sensor, type PAGM for CO2 and Halocarbon

© Danfoss | DCS (vt) | 2021.03

BC372016561395en-000101 | 9

Accuracy check should be performed once every 12 months to ensure peak performance of the unit 

see below guidelines.

Important:

 The accuracy check can only be performed when the unit is in Normal Operation – see 

above. Do NOT use pure refrigerant to perform this test as doing so will damage the unit.

PAGM-IR for CO2

•   Using a regulator, inflate a plastic bag (at least 20 L) with CO2 mixture of known concentration 

(recommended 5000 ppm) 

•   Insert the wand and seal the plastic bag opening while minimizing any leakage. Let the PGM 

stabilize over a few minutes

•   The PGM-IR should read /- 5% of the calibrated gas minus the ambient CO2 level (typically 

~390 ppm).

Example: unit exposed to 5000 ppm should read 4610 ppm +/- 5%, which is from 4380 – 4840 ppm

PAGM-IR for halogen gas

•   Set-up the unit to measure R134A gas,
•   Using a regulator, inflate a plastic bag (at least 20 L) with R134A gas mixture of known concertation 

(recommended 500 ppm) 

•   Insert the wand and seal the plastic bag opening while minimizing any leakage. Let the PGM 

stabilize over a few minutes

•  The PGM-IR should read /- 5% of the calibrated gas ppm value

Example: Unit exposed to 500ppm should read between 475 and 525ppm.

If the unit is outside the parameters please contact Danfoss technical support department  for further 

assistance.

5.3 Verification

Front

Remove 

screws (3)

Remove screws (2)

Left side

Rear

Remove 

screws (3)

Remove screws (2)

Right side

Note:

 When fitting the Hydrophobic Filters please observe the correct orientation as fail to do so will 

result in monitor fault condition – 

“NO FLOW” code <0800>

.

Содержание PAGM











Отзывы: