background image

Installation and service

Maximum compressor test pressure at low pressure side  

(suction side)

25 bar (g)

Maximum compressor test pressure at high pressure side  

(discharge side)

30 bar (g)

Maximum test pressure difference between high and low pressure side (to avoid 

that the internal compressor relief valve will open)

30 bar

System pressure test

Compressor connection 
to the system

Always use an inert gas such as nitrogen for 
the pressure test. Never use other gasses such 
as oxygen, dry air or acetylene. These gasses 
may form an inflammable mixture with the 
compressor oil. Always use the appropriate 
pressure regulator with gas cylinders. Any 
attempt to use a high pressure gas supply 

without a suitable pressure regulator can lead 
to personal injury or death as well as system 
damage.

The maximum allowed test pressures for NTZ 
compressors are:

New compressors have a protective nitrogen 
holding charge. 

R

Only remove the suction and discharge 

plugs just before connecting the compressor to 
the installation, so as to prevent air and moisture 
from entering the compressor. Remove the 
discharge plug first and the suction plug next; by 
proceeding as such, the nitrogen holding charge 
can escape via the discharge connection and 
the risk of an oil mist blow-out via the suction 
connection will be minimal.

Whenever possible the compressor must be the 
last component to be integrated in the system. It 
is advisable to braze the solder sleeves or service 
valves to the pipework before the compressor 
is mounted. when all brazing is finished and 
when the total system is ready, the compressor 
plugs can be removed and the compressor can 
be mounted to the system with a minimum 
exposure to ambient air. If this procedure is not 

possible, the sleeves or valves may be brazed to 
the pipes when mounted on the compressor. In 
this situation nitrogen or CO

2

 must be purged 

through the compressor via the schrader valve 
to prevent air and moisture ingress. Purging 
must start when the plugs are removed and 
maintained during the brazing process.

When rotolock valves are used on the 
compressor, they shall be closed immediately 
after mounting, thus keeping the compressor 
isolated from atmosphere or from a not yet 
dehydrated system.

Note:

 when the compressor is built into a "pack" 

or "rack" configuration which is not installed 
immediately on its final location, a vacuum pull-
down and moisture removal must be performed 
to the "pack" or "rack" as if it were a complete 
system (see below). the pack must be charged 
with nitrogen or CO

and open tubes must be 

blocked with caps or plugs.

27

AB245486497018en-000601

Application Guidelines

Содержание Maneurop NTZ





































Отзывы: