InstructIons for:
Belt Driven COMPreSSOrS
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
1. SAFetY inStrUCtiOnS
IMPORTANT:
PleASe reAD tHeSe inStrUCtiOnS CAreFUllY. nOte tHe SAFe OPerAtiOnAl reQUireMentS, WArninGS AnD CAUtiOnS.
USe tHe PrODUCt COrreCtlY AnD WitH CAre FOr tHe PUrPOSe FOr WHiCH it iS intenDeD. FAilUre tO DO SO MAY CAUSe
DAMAGe AnD/Or PerSOnAl inJUrY AnD Will invAliDAte tHe WArrAntY. PleASe KeeP inStrUCtiOnS SAFe FOr FUtUre USe.
1.1.
eleCtriCAl SAFetY.
WArninG!
It is the user’s responsibility to read, understand and comply with the following:
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs and
all electrical connections for wear or damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safety
devices. An rccB (residual current circuit Breaker) should be incorporated in the main distribution board. We also recommend that an rcD
(residual current Device) is used with all electrical products. It is particularly important to use an rcD with portable products that are plugged
into an electrical supply not protected by an rccB. If in doubt consult a qualified electrician. You may obtain a residual current Device by
contacting your sealey dealer.
You must
also read and understand the following instructions concerning electrical safety.
1.1.1. the
Electricity At Work Act 1989
requires all portable electrical appliances, if used on business premises, to be tested by
a qualified electrician, using a Portable Appliance tester (PAt), at least once a year.
1.1.2. the
Health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of appliance operators.
If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure the insulation on all cables and the product itself is safe before connecting to the mains power supply.
see 1.1.1. & 1.1.2. above and use a Portable Appliance tester (PAt).
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. regularly inspect power supply leads and plugs for wear or damage and connections to ensure that none is loose.
1.1.6.
Important:
Ensure the voltage marked on the product is the same as the power supply to be used, and check that the plug is fitted
with the correct capacity fuse.
1.1.7.
DO nOt
pull or carry the appliance by its power supply lead.
1.1.8.
DO nOt
pull plug from socket by the power cable.
1.1.9.
DO nOt
use worn or damage leads, plugs or connections. Immediately replace or have repaired by a qualified electrician.
1.1.10.
NOTE: THIS PRODUCT IS INTENDED FOR USE ON AN INDUSTRIAL 30AMP SUPPLY WHICH MUST BE INSTALLED BY A
QUALIFIED
ELECTRICIAN.
It may be possible to operate the compressor on a “Domestic” 13 amp outlet under the following
conditions: the mains supply must conform to IEE Wiring regulations, and the “spur” used to run the compressor must not include
any other socket which could be used for another appliance. the distance of the socket from the mains distribution point must not
exceed 5 metres.
An extension lead
must not be used
.
1.1.11.
note:
under certain conditions the compressor will draw more than 13 amps. consequently,
we recommend a 30 amp supply and suggest that a direct round pin plug/socket is installed by
a qualified electrician. In the event that you choose to use a domestic 13 amp supply,
we provide the plug wiring instructions as follows:
(uK only - see diagram at right). Ensure the unit is correctly earthed via a three-pin plug.
a) Connect the green/yellow earth wire to the earth terminal ‘e’.
b) Connect the brown live wire to the live terminal ‘l’.
c) Connect the blue neutral wire to the neutral terminal ‘n’.
d) ensure the plug is fitted with a 13 amp fuse.
e) After wiring, check that there are no bare wires, that all wires have been correctly
connected, that the cable outer insulation extends past the cable restraint and that the restraint is tight.
nOte:
IF THE FUSE BLOWS REPEATEDLY WHEN USED ON A DOMESTIC 13 AMP SUPPLY, CONTACT A QUALIFIED
ELECTRICIAN TO INSTALL A 30 AMP SUPPLY.
Blue
Neutral
Wire
Yellow & Green
Earth Wire
Cable
Restraint
Brown
Live
Wire
1.2.
GenerAl SAFetY inStrUCtiOnS
familiarise yourself with the application and limitations of the compressor.
Ensure the compressor is in good order and condition before use. If in any doubt do not use the unit and contact an electrician/service agent.
WArninG! Compressor must only be serviced by an authorised agent. DO nOt tamper with, or attempt to adjust, pressure switch or safety valve.
Before moving or maintaining the compressor
ensure that it is unplugged from the mains supply and that the tank pressure has been vented.
only use recommended attachments and parts. to use non-recommended items may be dangerous and will invalidate your warranty.
read the instructions regarding any accessory used with the compressor. Ensure the safe working pressure of any air appliance used exceeds the
compressor output pressure. If using a spray gun, check that the area selected for spraying is provided with air change system/ventilation.
Ensure the air supply valve is turned off before disconnecting the air supply hose.
use the compressor in a well ventilated area and ensure it is placed on a firm surface.
Keep tools and other items away from the compressor when it is in use and keep area clean and clear of unnecessary items.
Ensure the air hose is not tangled, twisted or pinched.
Keep children and unauthorised persons away from the work area.
DO nOt
dis-assemble compressor for any reason. the unit must be checked by qualified personnel only.
DO nOt
use the compressor outdoors, or in damp, or wet, locations and
DO nOt
operate within the vicinity of flammable liquids, gases or solids.
DO nOt
touch compressor cylinder, cylinder head or pipe from head to tank as these may be hot and will remain so for some time after shutdown.
DO nOt
attempt to move the compressor by pulling the air tool hose.
DO nOt
use the compressor for a task for which it is not designed.
DO nOt
deface the certification plate attached to the end of the compressor tank.
MoDEL no:
SA1050/3, SA1010/3, SA1015/3.v2, SA1020/3.v2
Original Language Version
sA1050/3, sA1010/3, sA1015/3.V2, sA1020/3.V2 Issue: 2 - 21/10/09
