Danfoss H1 078 Скачать руководство пользователя страница 41

Страница: 41 / 68

1. Install a new gasket (D150).

Proper Screen Orientation

P106 618E

D084

Incorrect screen
orientation

Correct screen
orientation

D094

2. If you removed screen (D084), install a new one. Install with the mesh facing outward (see drawing).

Install retaining ring (D098).

3. If previously removed, install orifices (F100) using a 3 mm internal hex wrench. Torque to 2.5 N•m [1.8

lbf•ft].

4. Install the control module and six cap screws (D250).
5. Using a 5 mm internal hex wrench, torque the cap screws (D250) to 13.3 N•m [9.8 lbf•ft].

Remove plug on top of control to ensure the swashplate feedback pin is properly positioned in the

center of the control module when installing control.

Control Module and Solenoid Removal/Installation

P106 650E

D025

D025A

D150

5 mm

13.5 N•m
[9.8 lbf•ft]

D250

D050 (3X)

D084

5 N•m [4 lbf•ft]

4 mm

5 N•m
[4 lbf•ft]

4 mm

F100 (2X)

D300 (2X)

2.5 N•m
[1.8 lbf•ft]

3 mm

D098

Service Manual

H1 Pumps 069/078, 089/100, 115/130, 147/165, 210/250

Minor Repair

Danfoss | May 2018

520L0848 | AX00000087en-US0308 | 41

Содержание H1 078





































































Результаты поиска

Содержание H1 078

Отзывы:

Бренды по названию

Популярные бренды

Danfoss H1 078, Руководство по обслуживанию

Результаты поиска

Содержание H1 078

Отзывы:

Бренды по названию

Популярные бренды