Danfoss ERC 21 Series, Руководство пользователя, Страница: 24 / 36

Compressor
Table 19: Compressor
Function Code Min. Max. Unit AP0 AP1 AP2 AP3 AP4 AP5
Compressor c--
Compressor minimum ON time C01 0 30 min 0.0 0.0 0.0 0.0 0.0 0.0
Compressor minimum OFF time C02 0 30 min 2.0 2.0 2.0 2.0 2.0 2.0
Compressor OFF delay at open door C04 0 900 sec 900.0 900.0 900.0 900.0 900.0 60.0
Zero crossing selection (YES / no) C70 no YES YES YES YES YES YES YES (1)
(1) This option is a default setting in the controller and cannot be changed. (1) This option is a default setting in the controller and cannot be changed.
Others
Function Code Min. Max. Unit AP0 AP1 AP2 AP3 AP4 AP5
Others o--
Delay of outputs at startup o01 0 600 sec 10 10 10 10 10 10 (1)
DI1 configuration
nC= Not configured; Sdc = Status display output, doo = Door
alarm with resumption, doA = Door alarm without resumption,
SCH = Main switch, nig = Day/ Night mode, rFd = Reference dis-
plasement, EAL = External alarm, dEF = Defrost, Pud = Pull
down; Sc = Condensor Sensor
o02 oFF Sc oFF oFF oFF oFF oFF oFF
Serial address o03 0 247 No 0 0 0 0 0 -
Password o05 0 999 No 0 0 0 0 0 0
Sensor type selection (n5=NTC 5K, n10=NTC10K, ptc=PTC,
pt1=PT1000)
o06
(2)
n5 ptc n10 n10 n10 n10 n10 n10
Cooling/Heating (rE=Cooling, Ht= Heating) o07 (2) rE Ht rE rE (1) rE (1) rE (1) Ht (1) rE
Display Resolution o15 0.1 1.0 0.1 0.1 0.1 0.1 0.1 0.1 (1)
Predefined applications o61 (2) AP0 AP5 AP0 AP1 AP2 AP3 AP4 AP5
Save settings as factory

WARNING:
The earlier factory settings are overwritten
o67 no YES no no no no no -
Display during defrost
Air=actual air temperature, FrE=freezed temperature, -d-="-d-"
is displayed
o91 -d- Air -d- - -d- -d- - -d-
(1)
(1)
This option is a default setting in the controller and cannot be changed.
(2) This parameter can only be set when regulation is stopped, i.e. “r12” is set to 0
(1)
This option is a default setting in the controller and cannot be changed.
(2) This parameter can only be set when regulation is stopped, i.e. “r12” is set to 0
Polarity
Table 20: Polarity
Function Code Min. Max. Unit AP0 AP1 AP2 AP3 AP4 AP5
Polarity P--
DI1 input polarity (nc/no)
no = normally open
nc = normally closed
P73 no nc no no no no no no
Key board lock (no / yes)(0=no, 1=yes) P76 no YES no no no no no -
Parameters: ERC 213
Configuration
Table 21: Configuration
Function Code Min. Max. Unit AP0 AP1 AP2 AP3 AP4 AP5 AP6 AP7
Configuration cFg
Main switch (-1=Service, 0=OFF, 1=ON) r12 -1 1 1 1 1 1 1 1 1 1
Predefined applications o61
(2)
AP0 AP7 AP0 AP1 AP2 AP3 AP4 AP5 AP6 AP7
Electronic refrigeration control, type ERC 21X
© Danfoss | Climate Solutions | 2023.01 BC194286421698en-000901 | 24