Danfoss DSH090 Скачать руководство пользователя страница 52

Страница: 52 / 74

Crankcase heater

The crankcase heaters are designed to protect the compressor against off-cycle migration of refrigerant.

For DSH090-105-120-140-161-184, the surface sump heater is located on the compressor shell. For better standby

energy consumption, Danfoss provides 48W and 80W two optional surface sump heater. The selection of surface

sump heater could be refered to

Table 32: Surface sump selection principle

Figure 57: DSH090 to 184

Table 32: Surface sump selection principle

Compressor Surrounding Ambient

Surface Sump Heater

Unit has enclosure, no wind

48W SSH

Unit has no enclosure, with wind

80W SSH

Unit has no enclosure, wind >5m/s (ft/s)& ambient temperature <-5°C

80W SSH + additional SSH/thermal insulation

For DSH240-295-381-485-600, the use of 75W crankcase heater is recommended.

Figure 58: DSH240 to DSH600

Danf

oss

9850380

The heater must be turned on whenever all the compressors are off. Crankcase heater accessories are available from

Danfoss (see section Accessories and Spare parts).

Liquid line solenoid valve (LLSV)

A Liquid line solenoid valve (LLSV) is used to isolate the liquid charge on the condenser side, thereby preventing

against charge transfer to the compressor during off -cycles. The quantity of refrigerant on the low-pressure side of

the system can be further reduced by using a pump down cycle in association with the LLSV.

Pump-down cycle

By decreasing pressure in the sump, pump down system:

• evacuates refrigerant from oil

• set the sump saturating pressure much lower than ambiance temperature and due to that, avoid refrigerant

condensation in the compressor.

Pump-down must be set higher than 1.7bar(g) (25 psig). For more details on pump-down cycle see section Control

logic.

Scroll compressors, DSH090 to DSH600 | Application

AB288965961751en-001402 | 52

Содержание DSH090











































































Результаты поиска

Содержание DSH090

Отзывы:

Бренды по названию

Популярные бренды

Danfoss DSH090, Инструкция по применению

Результаты поиска

Содержание DSH090

Отзывы:

Бренды по названию

Популярные бренды