D&K Monarchy Minikote EZ G3 Скачать руководство пользователя страница 9

Страница: 9 / 15

C. Threading the Film

C. Threading the Film
Remove the feed tray and the heatguard. Thread the

lm as

shown in the

gure on the right. Pull the

lm around the idler

rollers as shown. Do not mistake the reinforcing bar for the

Do not mistake the reinforcing bar for the

idler roller

idler roller. Make sure the glossy and dull sides of the

Make sure the glossy and dull sides of the

are as indicated in the diagram

are as indicated in the diagram. Position the threading board
provided.

Turn power and keyswitch to on.

Start the motor by pressing the “Fwd” but-
ton. Feed the threading board and

lm in

between the heat shoes. This will pull the

lm through the rollers until it comes out

the back of the laminator.

Slide the top and bottom

lm rolls from side

to side on the mandrels so that the

lm is

perfectly aligned top and bottom (Note:
overlap will cause the

lm to deposit resi-

due on the heat shoes and rollers, so this
procedure is critical). Replace feed tray
and heat guard.

DULL SID

SH I NY SID

DUL L SI D

S H I N Y S I

Laminator.com

www.laminator.com

Содержание Minikote EZ G3
















Результаты поиска

Содержание Minikote EZ G3

Отзывы:

Похожие инструкции для Minikote EZ G3

Бренды по названию

Популярные бренды

D&K Monarchy Minikote EZ G3, Руководство пользователя

Результаты поиска

Содержание Minikote EZ G3

Отзывы:

Похожие инструкции для Minikote EZ G3

Бренды по названию

Популярные бренды