99.824.05 2.4/04/16
DDS 54/500
4/12
DDS 54/500
English
Intended use
- Chain drive for electric opening of doors
- Operating voltage 24 V DC
- Useable in SHEV systems for operating smoke
extraction and fresh-air flaps
- It must always be possible to open the doors
and emergency exits of the building by han
(even in conjunction with electrically operated
door-locking systems)
- Only for inside mounting
Safety notes
Safety extra low voltage 24 V DC!
Do not connect directly to the mains supply!
- Connection has to be carried out only by an
authorized electrical specialist
- Danger of violent pressure in handaccessible area
- Keep away people from the operating area of
the drive
- Keep away children from the control
- Use only in dry rooms
- Use rain detector in locations where there is a risk
of rain
- Only for inside mountingt
- Just use unchanged original D+H parts
- Observe the bracket-set mounting instructions
Observe enclosed red safety slip!
Features
- Microprocessor controlled electronics
- Programmable with PLP1 and SCS
- Connection for electrical unlocking of door
- Drive not directly connected to door wing
- Manual opening is still possible
Drive unit with 2.5 m silicone cable.
Mounting brackets (incl. 4 x M5 screws) and
door bracket for mounting above door frame.
Extent of supply
Technical data
Type
DDS 54-500
Rated voltage
24 V DC, ± 15%; 1A
Nominal pressure force
500 N* +20% switch-off reserve
Nominal pull force
150 N
Opening width
ca. 90°
Runtime-OPEN
ca. 43s *
Delay (OPEN)
3s (for door unlocking)
/
Runtime-CLOSED
ca. 52 s * **
Duty cycle
30% (with cycle time 10 min.)
Lifetime
> 20 000 double strokes
Housing
Aluminium powder-coated
(~RAL 9006)
Protective system
IP 32
Temp. range
-5 ... +75°C
Fire stability
30 min / 300°C
Emission sound pressure
level
LpA ≤ 70 dB(A)
Delivery state
Active pinch protection activated *
* Programmable with PLP1 and SCS
**For safety reasons, the drive runs more slowly over the last 100 mm in the "CLOSE" direction.
A change in the sound is normal.
Forces
500 N
150 N
500 N
100 mm
Connection: Page 10
(WH) white
(BN) brown
(OG) orange
(YE) yellow
(GN) green
(PK) pink
(VT)
violet
(GY) grey
Pin Assignment
Option -BRV
WH (Mot. a)
BN (Mot. b)
GY (-BRV)
YE (TÖ)
Option -V-SZ
WH (Mot. a)
BN (Mot. b)
YE (TÖ)
GY (-BRV)
Standard
WH (Mot. a)
BN (Mot. b)
YE (TÖ)
Option V-SA
WH (Mot. a)
BN (Mot. b)
YE (TÖ)
GY (-BRV)
no
c
c
no
Option -SA-SZ
WH (Mot. a)
BN (Mot. b)
GY (-SA)
GN (-SA)
PK (-SZ)
YE (TÖ)
VT (-SZ)
TÖ = door unlocking
GN n.c.
PK (-SA)
VT (-SA)
c
no
c
no
PK (-SZ)
VT (-SZ)
GN n.c.
WARNING
Read all safety warnings, instructions, illustrations
and specifications provided with this product.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
Electrical devices, accessories, batteries and packa-
ging should be sorted for environmental-friendly
recycling. Do not dispose electrical devices and
batteries into household waste!
Only for EC countries:
According the European Guideline 2012/19/EU for
waste electrical and electronic equipment and its
implementation into national right, electrcal devices
that are no longer usable must be collected separa-
tely and disposed of in an environmentally correct
manner.
Disposal
Declaration of Conformity
We declare under our sole responsibility that the
product described under “Technical Data” is in
conformity with the following directives:
2014/30/EU, 2014/35/EU
Technical file at:
D+H Mechatronic AG, D-22949 Ammersbek
Dirk Dingfelder
Maik Schmees
Member of the Board
Authorized signatory, Technical Director
31.03.2016
Maintenance and cleaning
Maintenance work is only allowed when the device is in
a de-energized condition! Inspection and maintenance
has to be carried out according to D+H maintenance
notes. Only original D+H spare parts may be used.
Repair is to be carried out exclusively by D+H.
Wipe away debris or contamination with a dry, soft
cloth.
Do not use cleaning agents or solvents.
Guarantee
You will get 2 years guarantee for all D+H products
from date of verified handing over of the system up to
maximal 3 years after date of delivery, when
mounting and starting has been carried out by an
authorized D+H-distributor.
D+H guarantee is expired, with connection of D+H
components with external systems or with mixing of
D+H products with parts of other manufacturers.
