background image

A-Series rigging components

2.3  Cabinet rigging mechanism
The cabinets are mechanically connected to the Flying frame and

subsequent loudspeakers using the Front links on both sides of the

cabinet front and the central Splay link on the rear rigging strand

of the cabinet.
All necessary rigging components are mounted to the cabinet and

slide out or fold out when needed.

2.3.1  Front link mechanism

To extend and/or park the Front link, proceed as follows:

1. Slide out the Front link 

[1] up to its stop position.

Once the Front link is fully extended, it will be automatically

fixed in place by the spring steel sheet 

[2].

2. To slide the Front link back into its park position, press the

spring steel sheet towards the front grill.

3. Slide the Front link back into its park position.

2.3.2  Splay link mechanism

The Splay link is fixed in its park position ( ) by a Locking pin.
1. Release the Locking pin and fold out the Splay link.

2. To park the Splay link, proceed in reverse order and ensure

the extension tube is fully pushed in and the head is aligned

correspondingly, as shown in the graphic opposite.

 

d&b Z5458
AL Base plate Rigging manual 1.1 en

7

Содержание Z5458


















Отзывы: