background image

 

NL4 connection with cover plate
The NL4 connector socket of the cabinet's connector panel is

located in a recess to allow the use of the cover plate 

[1] together

with an NL4 cable connector, as shown in the graphic opposite.

Note: Neutrik NL4FC type connectors must be used for this

option.

To use the NL4 connection, proceed in the same manner as

described in the previous section.

2.3. Operation

NOTICE!

Only operate d&b loudspeakers with a correctly configured d&b

amplifier, otherwise there is a risk of damaging the loudspeaker

components.
Applicable d&b amplifiers:

30D/D20/D80.

Application

Setup

Cabinets per

channel

24S

24S

1

24S-D

24S-D

1

For applicable d&b amplifiers, the controller setups are available

in Dual Channel and/or Mix TOP/SUB mode.

2.3.1. Controller settings

For acoustic adjustment the functions CUT, HFA and CPL can be

selected.

CUT mode
Set to CUT, the low frequency level is reduced. The cabinets are

now configured for use with actively driven d&b subwoofers.

HFA mode
In HFA mode (High Frequency Attenuation), the HF response of the

system is rolled off. HFA provides a natural, balanced frequency

response when a cabinet is placed close to listeners in near field or

delay use.

High Frequency Attenuation begins gradually at 1 kHz, dropping

by approximately 3 dB at 10 kHz. This roll off mimics the decline

in frequency response experienced when listening to a system from

a distance in a typically reverberant room or auditorium.

NL4 cable connection with cover plate [1]

-5

0

5

10

-10

-15

-20

-25

-30

20

100

1k

10k

20k

Frequency response correction in HFA mode

 

d&b 24S/24S-D Manual 1.1 en

7

Содержание 24S















Отзывы: