background image

 

 

COMBIFLEX 

 

 

 

Page 22 

Replacements and repairs 

 

 

Safety is important with regards to 

all

 repair work on the drum. The following items 

must therefore be observed at  all times, as well as  the items under safety at  the 
beginning of the instruction manual. 

 

 

When replacing cylinders, the cylinder must always be filled with oil before it is sub-
jected to any load. It is therefore recommended that the cylinder is mounted on the 
fixed  part  of  the  frame  first,  after  which  the  cylinder  is  filled  with  oil  and  then 
mounted onto the opposing section. 

 

 

All maintenance and repair work on the drum may only be carried out after the ma-
chine  has  been  secured  against  accidental  starting by  lowering  the  machinery  at 
the  base  or  maintaining  it  in  transport  position,  the  tractor  is  braked,  the  engine 
stopped and the ignition key removed. 

 

 

For all repair work on the hydraulics, always pay close attention to safety. Before 
starting work, the pressure must be released from the hydraulic system and it is a 
requirement that the section is supported from below. 
 

 

 

After any repair work on the hydraulic system, all air must be removed from the sys-
tem  before  use  in  order  to  protect  against  breakdown  and  personal 
injury. 

 

Hydraulics 

Replacing cylinder for unfolding and folding of wheel frame 

Repairs  are  carried  out  with  the  wheel  frame  unfolded  into  working  position  and 
resting on the sub-frame. 

 

 

1.

 

Release the pressure from the cylinder. 

2.

 

Remove the hoses. 

3.

 

Remove  cotters  and  studs  and  the  cyl-
inder is free. 

4.

 

Mount the new or repaired cylinder. Re-
member to secure the stud's grip in the 
stud stopper and secure the studs with 
cotters. 

5.

 

Mount  the  hoses.  After  mounting,  en-
sure  that  there  is  no  risk  of  tearing  or 
crushing the hoses. 

 

 
 

Содержание COMBIFLEX






























Отзывы: