manualshive.com logo in svg

DAL-BO Maxiroll 1030 2008, Руководство пользователя

Поделиться
Скачать
DAL-BO Maxiroll 1030 2008 Скачать руководство пользователя страница 28

 

 

Maxiroll 2008 

 

 

 

Page 28 
 

 

 

Activate  extend/retract  cylinders  after  fitting  until  they  show  a  little  move-
ment.  Reverse  cylinders  until  they  return  to  start  position.  Move  cylinders 
backwards  and  forward  several  times.  Raise  roller  fully  onto  wheels,  extend 
side sections fully to bleed system. 
 

 

 
Ensure no personnel are within the extension radius of the side sections. 

Replacing gaskets for side section fold/unfold 

Fig. 24 

 

 

 
1.

 

For cylinder removal, see ”Replacing extend cylinder for folding side sec-
tions”. 

2.

 

Drain oil from cylinder by moving ram carefully backwards and forwards. 

3.

 

Extend ram to centre position. Unscrew upper part (pos. 3) from cylinder 
tube (pos. 1). Use special tool to remove upper part. If upper part is stuck, 
heat front of sleeve. When upper part is detached from cylinder tube, pull 
ram up towards upper part and remove completely from cylinder tube. 

4.

 

Remove lock nut securing collar show (pos. 4). 

5.

 

Remove collar shoe (pos. 4) from ram. 

6.

 

Remove upper part (pos. 3) from ram. 

7.

 

Remove gaskets in upper part and collar shoe, (pos. 5+6+7+8+9). 

8.

 

Clean  all parts and check for particles  etc. Check for rust around scraper 
ring (pos. 5) in upper part. If detected, remove thoroughly. 

Содержание Maxiroll 1030 2008











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды