Daktronics VIP-5000 Series Скачать руководство пользователя страница 43

Страница: 43 / 62

– 39 –

Power Control

Serial Loopback Test

This test verifies the serial cable functionality of

a configured power relay control device.

After Clicking

Run Loopback Test

, the operator

is prompted to connect the transmit and

receive pins on the serial cable. Refer to

Figure 87

. Click

Yes

to start the test or

exit.
After the loopback test is completed, a

success or failure banner opens at the top of the page.

ISP

The ISP relay is a standard power control relay.

Refer to

Power Control (p. 29)

for information

about configuring relays. Click

Cycle

to restart

the ISP relay (the power is turned off and then

back on). Refer to

Figure 88

After the relay

test is completed, a success or failure banner

opens at the top of the page.

Player

The Player relay is a standard power control

relay. Refer to

Power Control (p. 29)

for

information about configuring relays. Click

Cycle

to restart the Player relay (the power is

turned off and then back on). Refer to

Figure 88

After the relay test is completed, a

success or failure banner opens at the top of

the page.

Display Face

The Display Face relay is a standard power

control relay. Refer to

Power Control (p. 29)

for information about configuring relays. Click

On/Off

to restart the Display Face relay (the power is turned either on or off). Refer to

Figure 88

. After the relay test is completed, a success or failure banner opens at the top

of the page.

Aux

The Aux relay is a standard power control relay. Refer to

Power Control (p. 29)

for

information about configuring relays. In the example shown in

Figure 88

, there are two

options for starting testing this relay. Click

On/Off

to restart the Aux relay (the power is

turned either on or off) or click

Cycle

to restart the Aux relay (the power is turned off and

then back on). After the relay test is completed, a success or failure banner opens at the

top of the page.

Figure 87:

Serial Loopback Test Prompt

Figure 88:

Power Relay Controls

Содержание VIP-5000 Series































































Результаты поиска

Содержание VIP-5000 Series

Отзывы:

Daktronics VIP-5000 Series, Руководство по эксплуатации, Страница: 43 / 62

Результаты поиска

Содержание VIP-5000 Series

Отзывы: