manualshive.com logo in svg

Daktronics TI-2022, Руководство пользователя

Поделиться
Скачать
Daktronics TI-2022 Скачать руководство пользователя страница 17

Display Maintenance

13

5  Display Maintenance

Disconnect power before doing any repair or maintenance work on the display� 

Permit only qualified service personnel to access internal display electronics. 

Disconnect power when not using the display� 

Display Components

The TI-2022 uses a single printed circuit board (PCB) that contains all of the electronics 

needed to make this system work: digit LEDs, control processors, power input connectors, 

horn, and other components. All switches, power systems, and input/output terminations 

are connected to the PCB.
As shown in 

Figure 12

, the PCB is attached to the front panel of the display. Refer to 

Replacing the Digit/Driver Printed Circuit Board (p.14)

 for instructions on accessing and 

replacing the PCB.

Screw

(HC-1489)

Battery 

(BT-1014)

8-32 Nut 

(HC-1354)

Nut securing 

signal jack

Printed Circuit Board

(Indoor: 0P-1153-0001)

(Outdoor: 0P-1153-0003)

Rear 

Panel

Front Panel

Spacer 

(HE-1357)

Printed Circuit Board

(Indoor: 0P-1153-0002)

(Outdoor: 0P-1153-0004)

Figure 12: 

TI-2022 Exploded View

Содержание TI-2022

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды