background image

Introduction

1

1  Introduction

This manual explains the installation, maintenance, and troubleshooting of a Sportsound

®

 

SSN-250 Indoor Audio System with integrated audio control rack. For additional 

information regarding safety, installation, operation, or service, refer to 

Section 7: 

Daktronics Exchange and Repair & Return Programs (p�15)

. This manual is not specific 

to a particular installation. Project-specific information takes precedence over any other 

general information in this manual. 

Important Safeguards

• 

Read and understand all instructions before beginning the installation process� 

• 

Disconnect system power when not in use or when servicing� 

• 

Do not modify the cabinet structure or attach any panels or coverings without the 

express written consent of Daktronics� 

• 

Do not disassemble control equipment or electronic controls of the system; failure to 

follow this safeguard will make the warranty null and void� 

• 

Do not drop the control equipment or allow it to get wet� 

• 

Always turn off and/or unplug the control equipment when it is not in use� This keeps 

equipment protected from power spikes and lightning� 

• 

Never yank the power cord from the outlet� Grasp the plug and pull to disconnect� 

• 

Do not let any power cord touch hot surfaces or hang over the edge of a table that 

would damage or cut the cord� Arrange the cord with care so that it will not be 

tripped over� 

• 

Inspect equipment for shipping damage such as rattles and dents, and verify that 

all equipment is included as itemized on the packing slip� Immediately report any 

problems to Daktronics; save all packing materials if exchange is necessary� 

Resources

Figure 1

 illustrates a Daktronics drawing label. 

This manual refers to drawings by listing the last 

set of digits. In the example, the drawing would 

be referred to as 

DWG-1007804

. All references to 

drawing numbers, appendices, figures, or other 

manuals are presented in bold typeface. Any 

drawings referenced in a particular section are 

listed at the beginning of it as shown below: 

Reference Drawing:

System Riser Diagram .......................................................................................

DWG-1007804

Daktronics identifies manuals by the DD or ED number located on the cover page. 

Daktronics has a searchable knowledgebase of common questions and troubleshooting 

tips: 

www.daktronics.com/support

Visit the Daktronics Support YouTube channel to learn how 

to properly operate Sportsound racks: 

www.youtube.com/

DaktronicsSupport

Drawing Number

Figure 1: 

Drawing Label

Содержание SPORTSOUND SSN-250





































Отзывы: