background image

DD5075265
Rev 00
3 June 2022

NPN-X200/X400 Series Speed Frame Substructure & Panel Quick Guide

Page 3 of 4

201 Daktronics Drive

Brookings, SD 57006-5128

www.daktronics.com/support

800.325.8766

Install Seismic Clips

1. 

Place seismic clip (0M-4983082) up to the secured mounting points in 

the frame. Refer to 

Figure 12

.

Note: 

Ensure that the flange of the clip falls in the track opening and is 

pressed against the side of the threaded clip.

2. 

Mark the location of one of the two holes in the clip to match the drill 

with the screw hole. Remove the clip.

3. 

Drill a 

5

/

32

" diameter hole at the marked location.

4. 

Replace the clip and secure with a #10-12 x 

3

/

8

" sheet metal screw 

(HC-1186) using the pre-drilled hole. Refer to 

Figure 13

.

5. 

Repeat clip installation steps for all frame mounting locations in the 

display.

Panel Installation

Route Power & Signal

1. 

Identify which panels will require power and/or signal inputs. Refer to 

the contract-specific Shop and Riser Drawings for details.

2. 

Use the pass-through holes and notches in the frame to route the 

power and signal input cables from the input to the required input 

panel location prior to panel installation.

Note: 

Incoming power and signal cables external to the display 

cannot be routed after panels are installed.

Figure 12: 

Position Seismic Clip

Figure 13: 

Secure Clip Screws

Install First Panel

1. 

Remove the first panel from its packaging and install the hardware.

Figure 14: 

Install Hardware in First Panel

 

a. 

Install four M6 bolts (Daktronics 

part number HC-1795) through 

the front of the panel so the 

threads are engaged but not 

protruding out the rear of the 

panel. Refer to 

Figure 14

 and 

Figure 15

.

b. 

Install four M8 bolts (HC-4884317) 

through the rear of the panel so 

the threads are engaged but 

not tightened all the way. Leave 

~

1

/

4

" between the bolt flange and 

the rear of the panel. Refer to 

Figure 14

 and 

Figure 15

.

2. 

Route the Cat 6 signal cable and/

or male end of the AC power input 

cable through the rectangular cutout in the panel prior to placing the 

panel if installing a panel where power/signal needs to land.

Note: 

Depending on the structure and access to the rear of the 

display, it may be very difficult or impossible to route power 

cables into the panel after the panel is secured to the tube.

Figure 15: 

Leave 

1

/

4

" between Bolt 

Flange & Panel Rear

1

/

4

"

Figure 16: 

Remove Nuts from Cover

 

a. 

Remove the two nuts (circled in red in 

Figure 16

) securing the 

appropriate cover on the inside of the cabinet.

b. 

Use a Phillips screwdriver to 

remove the two screws securing 

the power cable and the 

mounting bracket at the bottom 

of the panel. Refer to 

Figure 17

.

c. 

Install the power input cable 

through the rear of the panel 

and plug in the cable. Refer to 

Figure 18

.

3. 

Hang the M8 bolt heads through the keyholes in the frames to place 

the panel in the bottom center-most display position.

4. 

Repeat 

Steps 1–3

 for the remainder of the first row. Refer to 

Figure 19

.

Figure 19: 

Install Remaining Panels in Bottom Row

Figure 17: 

Remove Screws from 

Mounting Bracket

Figure 18: 

Install Power Input Cable

Отзывы: