background image

RS422 

 

Reference Drawings: 

 System 

Riser 

Diagram, RS422 ....................................

Drawing A-174135

 

 

Schematic, Signal Wiring Internal, w/QC PCB ............

Drawing B-177662 

 

 
The RS422 controlled display requires the use of signal converter (0A-1127-0237) 
near the computer. From the signal converter, cable is run to the surge board 
assembly in the display. The cable from the signal converter to the display must be 
routed though conduit. 

Do not run signal and display power through the same 

conduit.

 Refer to 

Drawing A-174135

 and 

Figure 24

 for system layout. 

 

1. 

If using a quick connect cable, connect from the signal converter to a 
junction box at the display, and from there to J32 on the back of the display

 

2. 

When connecting directly to the display, terminate one end at the signal 
converter and the other end of the wire to the 6-position terminal block on 
the surge board assembly labeled “RS422 IN” (A34-TB1). The connection 
from the surge board to the controller is already completed. Refer to 

Figure 

25

 

and 

Drawing

 

B-177662

 for the terminal block wiring

 

 

 

Figure 24: RS422 Display Layout 

 

Electrical Installation 
 

3-13

Содержание Galaxy AF-3165


































































































Отзывы: