background image

3. Phoenix

ä

-Style Connectors: 

 

 

Figure 12: 

Phoenix-

Style

 

Connector 

Phoenix-style connectors, which are usually green, are often 
used for signal termination on circuit boards. Refer to

 Figure 

12 

on the right. Strip one-quarter inch of insulation from the 

wire prior to termination. To remove a wire, turn the above 
screw counter-clockwise to loosen the connector's grip on the 
wire. To insert a wire, push the bare wire into the connector, 
and turn the above screw clockwise to lock the wire into 
place. 

 

4. Mate-n-Lok

ä

 Connectors: 

 

The Mate-n-Lok connectors found in the signs are white and 
come in a variety of sizes. 

Figure 13

 on the right illustrates a 

four-pin Mate-n-Lok connector. To remove the plug form the 
jack, squeeze the plastic locking clasps on the side of the 
plug and pull it from the jack. 

 

 

 

Figure 13: 

Mate-n-

Lok Connector 

5.  Phone Jacks (RJ11/RJ45 Connectors): 

RJ connectors are similar to the telephone connectors found 
in homes and are used on the ends of RJ11 or RJ45 cable. In 
order to remove this plug from the jack, depress the small 
clip on the underside of the plug. Before replacing an RJ 
connector, spray it with DeoxIT

 contact cleaner to remove 

any foreign matter that may cause signal problems. In 
addition, apply a generous amount of CaiLube

 protector 

paste to the plug before inserting it into the jack. This paste 
will protect both the plug and the jack from corrosion.  

3.2  Control Cable Categories 

The conductor connector used in the network is an industry standard, 
6-pin RJ11. This connector can be found on 
many telephones and LANs. 

 

 

Figure 14: 

6-Conductor RJ11 Connector and 

Cable 

 
The cable used in the network is a standard flat 
six-conductor telephone cable (standard flipped 
cable). Refer to 

Figure 14 

on the right. This 

cable has one end that is the mirror image of the 
other end (i.e. the cable is flipped). Refer to 

Figure 15 

on the following page

 

for a standard 

flipped cable.

 

 
 
 
 

Electrical Installation 

 

3-2

Содержание Galaxy AF-3010







































































Отзывы: