manualshive.com logo in svg

Daktronics DVX-1200 Series, Инструкция по установке и обслуживанию, Страница: 7 / 10

Поделиться
Скачать
Daktronics DVX-1200 Series Скачать руководство пользователя страница 7

DVX-1200/2200/2210 Series Panel Installation & Service Quick Guide

Page 7 of 10

DD5166395
Rev 05
20 October 2023

201 Daktronics Drive

Brookings, SD 57006-5128

www.daktronics.com/support

800.325.8766

Receiver Card

To remove a receiver card, follow these steps:

1. 

Disconnect power to the display.

2. 

Unlatch the power box to open the box. Refer to 

Figure 55

.

3. 

Use a screwdriver to remove the corner screws from the receiver card. 

Refer to 

Figure 64

.

Figure 64: 

Remove Corner Screws

4. 

Grasp the receiver card by the corners and remove the card. Refer to 

Figure 65

 and 

Figure 66

.

Figure 65: 

Remove Receiver Card

Reverse these steps to install a receiver card.

Hub Board

1. 

Disconnect power to the display.

2. 

Unlatch the power box to open the box. Refer to 

Figure 55

.

3. 

Disconnect all cables from the module. Refer to 

Figure 67

.

4. 

Disconnect the cable from the power supply. Refer to 

Figure 68

Figure 67: 

Disconnect Cables from 

Module

 

Figure 68: 

Disconnect Cables from 

Power Supply

Figure 66: 

Receiver Card Removed

5. 

Disconnect the signal cable on both left and right sides of the hub 

board. Refer to 

Figure 69

.

Figure 69: 

Disconnect Signal Cable

6. 

Remove the receiver card. Refer to 

Receiver Card (p.7)

.

7. 

Use a screwdriver to remove the screws securing the hub board to the 

power box. Refer to 

Figure 70

.

Figure 70: 

Remove Screws from Hub Board

8. 

Pull the hub board gently outward to remove it from the power box.

Reverse these steps to install a hub board. 

Fan

1. 

Disconnect the fan cable from the hub board. Refer to 

Figure 71

. The 

fan is mounted to the right hub board.

2. 

Use a screwdriver to remove the screws securing the fan to the hub 

board. Refer to 

Figure 72

.

Figure 71: 

Disconnect Fan

3. 

Pull the fan gently outward to remove it from the hub board.

Reverse these steps to install a fan. 

Power Supply

To remove a power supply from a front- or rear-access display, follow these 

steps:

1. 

Disconnect power to the display.

Figure 72: 

Disconnect Fan Connector 

2. 

Unlatch the power box to open the box. Refer to 

Figure 55

.

3. 

Use a screwdriver to remove the screws and cables 

from both sides of the power supply. Refer to 

Figure 73

.

Figure 73: 

Remove Screws & Cables from Power Supply

4. 

Use a screwdriver to remove the four corner nuts from the power 

supply. Refer to 

Figure 74

.

5. 

Remove the thermal pad from the old power supply and apply it to the 

new power supply. Refer to 

Figure 75.

Figure 74: 

Remove Four Corner Nuts

 

6. 

Remove the power supply. Refer to 

Figure 76

.

Figure 76: 

Thermal Pad on Power 

Supply

Reverse these steps to install a power supply in a front- or rear-access 

display.

Figure 75: 

Remove Power Supply

Содержание DVX-1200 Series











Отзывы:

Нет отзывов