manualshive.com logo in svg

Daktronics BA-1018, Руководство пользователя

Поделиться
Скачать
Daktronics BA-1018 Скачать руководство пользователя страница 73

 

 

Note:

 If you are accessing the unit from the rear, follow this procedure: 

First, remove the rear access panel (explained in preceding subsection.): 
While holding onto the module, push it out and turn it in such a manner 
(generally a sideways, diagonal turn) that it will fit through the frame 
opening; then pull the module back through the opening in the frame. 
Carefully disconnect the ribbon cables. Once again, label the cables, 
indicating which cable was removed from which connector; the labeling 
will be helpful when reconnecting.

 

 

When installing a module, reverse the previous steps and take note of the following 
points: 

 

 

Weatherstripping on the back edge of the module must be intact and in 
good condition to prevent water from seeping into the display. 

 

 

Module latches must be fully engaged to create a watertight seal around the 
edge of the module. The module should be firmly seated against the display 
when the latches are fully engaged. 

 

Each module assembly contains a module housing (containing LEDs and the driver 
board) and a louver assembly. 

Drawings B-126111 

and

 B-126112

 illustrate the 

various module components. 
 
Individual components such as louvers can be removed for service, but Daktronics 
recommends that the module be kept intact and that the entire assembly be sent in for 
repair or replacement. 
 

For displays installed after 11/29/05 
 

The module and driver are a single functional unit. Each module assembly is made 
up of a module housing (containing LEDs and the driver) and a louver assembly. 

 

1. 

Locate

 

the latch access fasteners on the module (one is centered below the 

second row of pixels 
and one is centered 
above the bottom 
two rows)

 

9-8 TNMC 

Maintenance 

2. 

With a 

1

/

8

" hex 

wrench, turn both 
latch access 
fasteners a quarter 
turn counter-
clockwise to open as 
shown in

 

Figure 18

 – 

and the clockwise to 
close.

 

3. 

Gently pull

 

the 

module far enough 
forward to reach behind the back and disconnect the power and ribbon 
cables

 

 

Figure 18

:

 

Removing a Module

 

Содержание BA-1018

























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды