8
MAN#650536:A
oil psi
Engine oil temperature setup menu
•
Press and release the switch until “
oil psi
” is displayed, then press and hold the switch until the display blanks.
•
Release the switch. The display will show “
ON
” or “
OFF
” depending on whether the reading is currently enabled.
•
If
ON
is selected, the next option is “
warning
” or “
DONE
”.
•
Press and release the switch to change the selection, press and hold the switch to select it.
warning
Low oil pressure warning setup
•
Press and release the switch until “
warning
” is displayed, then press and hold the switch until the display blanks.
•
Release the switch. The display will show “
LO
”, the current warning (0 – 30), and “
warning
”.
•
Press and release the switch to change the value, press and hold the switch to select it.
Display
Message display option menu
•
Press and release the switch until “
display
” is displayed, then press and hold the switch until the display blanks.
•
Release the switch. The display will show “
contrast
”, “
prfm disp
”, “
indicators
”, “
MBMs
”, or “
DONE
”.
•
Press and release the switch to change the selection, press and hold the switch to select it.
contrast
Message screen contrast adjust
•
Press and release the switch until “
contrast
” is displayed, then press and hold the switch until the display blanks.
•
Press and hold the switch to adjust the contrast. Each time the switch is pressed it will alternate between increasing and
decreasing the contrast. To exit, wait with no switch press for a few seconds.
prfm disp
Display performance readings
The performance readings are high speed recall, high RPM recall, 0-60 time, ¼ mile speed, and ¼ mile time.
•
Press and release the switch until “
prfm disp
” is displayed with the current setting (“
HIDE
” or “
shOw
”). To change the
setting press and hold the switch until the display blanks.
•
Press and release the switch to change between the settings, press and hold the switch to select it.
indicators
Display indicators on gauge face
To display turn signal, high beam, low oil, and neutral indicators on the gauge face.
•
Press and release the switch until “
indicators
” is displayed with the current setting (“
HIDE
” or “
shOw
”). To change the
setting press and hold the switch until the display blanks.
MBms
Display which MBMs are connected and adjust warnings
To troubleshoot MBM connections, the speedometer can indicate which senders it sees connected.
•
Press and release the switch until “
MBMs
” is displayed. The screen will show either a letter pair or a “--” for each module.
•
Press and hold the switch to toggle through the available warning settings. (see the separate MBM manual for additional
details)
Gear indicator setup
This gauge has an indicator for gear position displayed next to the clock. The gauge can learn the gear ratios based on
speed and RPM so no sensors are needed, just what you’ve already connected. It will work with 4, 5, 6, or 7 speed transmissions.
The factory preset option will preset the indicator to work with a stock 5 or 6 speed drive train. With a stock 6 speed, there will be
a slight delay the first time you shift to sixth gear as the system verifies the gear. You can also program each gear position for
aftermarket transmissions or if you’ve changed wheel size or sprocket size. To program the gear positions, begin at a section of
road where you can gradually shift through all of the gears. Press and hold the switch while turning the key on and starting the
engine. Once the engine is running, release the switch.
•
Press and release the switch until “
gear
” is displayed, press and hold the switch the display blanks.
•
The display will show “
preset
”, or “
learn
”, or “
done
”. “
preset
” will set the indicator for an original factory transmission.
“
learn
” allows it to work with virtually any transmission option.
•
To program each gear individually, press and release the switch until “
learn
” is displayed, then press and hold the switch.
•
The message will show “
lo tch
” if the engine RPM is below 1500, or “
lo spd
” if the vehicle speed is below 5 MPH.
•
Begin driving in 1
st
gear. The display should show “
gear 1
” and the “
1
” should be flashing. Drive at a steady speed around
2,700 RPM until the “
1
” goes steady and then changes to a flashing “
2
”, it should only take about 20 seconds if the speed and
RPMs are steady.
Optional: If the gear does not stop flashing you can manually override and jump to the next gear by pressing and
releasing the switch to store the gear position quicker.
•
Shift to 2
nd
gear and drive at a steady speed.
•
Wait until the “
2
” goes steady and then changes to a flashing “
3
”. Shift to 3rd gear.
Optional: If the gears do not stop flashing you can manually override and jump to the next gear by pressing and releasing
the switch to store the gear position quicker.
•
Repeat this through each gear. When you are done, come to a complete stop or press and hold the switch until the display shows
“
done
” and then release it.
•
Press and release the switch to restart the gauges in normal operation, verify the gear position by riding through each gear and
seeing if positions agree.
