[7]
MAN #650506C
VHX setup:
✓
Ensure all desired BIM units are connected to the control box with the appropriate data cables.
✓
When doing the calibration, the car must be driven.
o
The engine must be started when entering setup.
o
One should be in an empty part of a parking lot
1. Hold SW1 (I) switch for the VHX control and start the engine.
2. Release SW1 (I). The LCDs will display
SETUP SPEED
and
SETUP
.
3. Tap SW1 (I) until the first LCD shows
SETUP BIM
.
4. Press and hold SW1 (I).
a. The message display will show
SCANNING
… Release SW1 (I).
b. The display will scroll through the 16 possible channels used.
c. If
FOUND xx
and
00 ERRORS
is shown (X = should be the number of BIMs used):
1. BIM-01-2 uses no channels
ii. Tap SW1 (I) until
BIM SCAN
is shown
– jump to step 5
d. If
FOUND 00
and
XX ERRORS
is shown (X = a number):
i. If multiple BIM units are installed, the display may also show
FOUND 01
and
00 ERRORS
.
ii. F
ollow the “Change ID” (Page 4) to correct conflicts, the enter setup again start over.
e. If
FOUND 00
and
00 ERRORS
is shown:
i. Check and reseat all BIM connections.
ii. Tap SW1 until
BIM SCAN
is displayed.
iii. Press and hold SW1 (I) to scan for modules again.
5. Tap SW1 (I) until the display shows
BIM SETUP
.
a. The BIM setup options are
SCAN
,
SETUP
, and
DONE
.
6. Press and hold SW1 until the message changes to
BIM CH 08
and
COMPASS
.
a. Default channel is 08 if not conflicting with another BIM.
7. Press and hold SW1 (I) until
CH 08 LABEL
and
COMPASS
.
a. Label cannot be changed.
8. Press and hold SW1 (I) until
CH 08 LOW
and
WARN SET
is displayed.
9. Release SW1 (I) and the display will show
AIR TEMP -40F
and
N
.
a.
AIR TEMP -40C
if water sender was set to Celsius.
10. Tap SW1 (I) to increase the temp reading to desired low temp warning.
a. Temp scale ranges from -32 to 72.
b. Many like 32F (0 C) to warn of possible icing conditions.
11. Press and hold SW1 (I) to save low temp warning.
12. Release SW1 (I), display will show
COMPASS N
and
ADJUST 00
.
13. Refer to the magnetic chart on page [
4
]
– tap SW1 (I) to change magnetic offset.
a. The number will start at
00
, then goes up to
31
then cycles to
-32
and counts up.
14. Tap SW1 (I) to change the magnetic offset for your location.
a. Refer to the magnetic compass map on page [4].
15. Press and hold SW1 to save, display will show
CAL COMPASS
and
BEGIN
, then release.
16. Press and hold SW1 (I) until the display shows
CAL COMPASS
and
CIRCLE
, then release.
17. Slowly drive two large circles, or a square in a parking lot.
18. Come to a stop after completing two circles.
19. Press and hold SW1 (I) until
BIM SETUP
and
DONE
is displayed.
20. Press and hold SW1 (I) until a large
DONE
appears.
21. Release SW1 (I) and the display will show
BIM DONE
.
22. Press and hold SW1 (I) until a large
DONE
appears, release SW1 (I).
23. If you have other BIM modules to setup, please follow the instructions for each BIM.
