DAKEWE 6250 Скачать руководство пользователя страница 9

Страница: 9 / 47

Dakewe(Shenzhen)Medical Equipment Co,. Ltd

V4.1

Safety

2.1

Safety Precautions

This User Manual contains important information related to operational safety and equipment

maintenance.

As an important part of the product, the User Manual must be read carefully before installation

and use, and always be placed near the instrument.

Electrical safety of instruments conform to IEC 61010-1:2018 Safety requirements for

electrical equipment for measurement, control and laboratory use - Part 1: General

requirements, IEC 61010-2:2018 Safety requirements for electrical equipment for

measurement, control and laboratory - Part 2-101 Special requirements for in vitro diagnostic

(IVD) medical devices".

This instrument meets the requirements for radiated interference and interference immunity

specified in the EMC standards IEC 61326-1:2012 and IEC 61326-2-6:2012

The performance indicators of the instrument are in line with Dakewe's technical requirements

of the cryostat.

In order to maintain this condition and ensure safe operation, the user must comply with all

safety precautions and warnings in this User Manual.

⚫

Always observe the safety and precautions described in this Chapter.

⚫

Even if you are already familiar with the operation and use of other

Dakewe products, be sure to read these instructions.

⚫

Do not remove or modify the protective devices on the instrument and

accessories. Only Dakewe-certified qualified maintenance personnel can

repair the instrument and dispose of the instrument’s internal

components.

⚫

The instrument is designed and manufactured with advanced technology

and complies with relevant safety technical standards and specifications.

Improper instrument operation or handling can result in injury to the

user or other personnel, damage to the instrument and other property

damage. The instrument must be used for its intended use and only when

all safety functions are in proper working condition. Faults that are

detrimental to safety must be corrected immediately.

⚫

Only original spare parts and allowed original accessories can be used.

⚫

Only use original spare parts and permitted original accessories.

Be sure to observe the safety instructions and warnings in this Chapter.

Even if you are already familiar with the operation and use of the product, be sure to read

these instructions.

Содержание 6250
















































Результаты поиска

Содержание 6250

Отзывы:

Похожие инструкции для 6250

Бренды по названию

Популярные бренды

DAKEWE 6250, Руководство пользователя

Результаты поиска

Содержание 6250

Отзывы:

Похожие инструкции для 6250

Бренды по названию

Популярные бренды