manualshive.com logo in svg

DaimlerChrysler Jeep Grand Cherokee 2002, Руководство по обслуживанию

Поделиться
Скачать
DaimlerChrysler Jeep Grand Cherokee 2002 Скачать руководство пользователя страница 41

Symptom:

P0110-INTAKE AIR TEMP SENSOR CIRCUIT SIGNAL VOLTAGE
TOO LOW

When Monitored and Set Condition:

P0110-INTAKE AIR TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW

When Monitored:

With the ignition on.

Set Condition:

The Intake Air Temperature Sensor Signal voltage is below 0.073 volt.

POSSIBLE CAUSES

INTERMITTENT CONDITION

IAT SENSOR

INTAKE AIR TEMP SENSOR SIGNAL CIRCUIT SHORTED TO GROUND

INTAKE AIR TEMP SENSOR SIGNAL CIRCUIT SHORTED TO SENSOR GROUND

ENGINE CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, erase ECM DTCs.
Monitor the DRB for ECM DTCs.
Did this DTC set again?

All

Yes

→

Go To

2

No

→

Go To

6

2

Turn the ignition off.
Disconnect the IAT Sensor harness connector.
Turn the ignition on.
Monitor the DRB for ECM DTCs.
Does the DRB display P0110 INTAKE AIR TEMP SIGNAL VOLTAGE TOO HIGH?

All

Yes

→

Replace the Intake Air Temperature Sensor.
Perform ROAD TEST VERIFICATION - VER-2.

No

→

Go To

3

3

Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the IAT Sensor harness connector.
Measure the resistance between ground and the Intake Air Temperature Sensor
Signal circuit.
Is the resistance above 100 kohms?

All

Yes

→

Go To

4

No

→

Repair the Intake Air Temperature Sensor Signal circuit for a
short to ground.
Perform ROAD TEST VERIFICATION - VER-2.

33

DRIVEABILITY - DIESEL

ProCarManuals.com

Содержание Jeep Grand Cherokee 2002





























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды