manualshive.com logo in svg

DaimlerChrysler Jeep Grand Cherokee 2002, Руководство по обслуживанию

Поделиться
Скачать
DaimlerChrysler Jeep Grand Cherokee 2002 Скачать руководство пользователя страница 242

Symptom:

*ENGINE CRANKS BUT WILL NOT START

POSSIBLE CAUSES

CHECK CAMSHAFT POSITION SENSOR SIGNAL

CHECK CRANKSHAFT POSITION SENSOR SIGNAL

CHECKING FOR ECM CODES

CHECKING FOR SKIM CODES

CHECKING THE ECT SENSOR

CHECKING THE GLOW PLUG OPERATION

ENGINE CONTROL MODULE

ENGINE DRIVE GEAR/SPROCKET

FUEL INJECTOR DRIVER CIRCUIT(S) SHORTED TO GROUND

FUEL PRESSURE SENSOR

FUEL PRESSURE SENSOR 5-VOLT SUPPLY CIRCUIT OPEN

FUEL PRESSURE SENSOR SIGNAL CIRCUIT OPEN

FUEL SUPPLY CONTAMINATION

FUEL SYSTEM PRESSURE MECHANICAL

FUEL SYSTEM RESTRICTION

SENSOR GROUND OPEN

TEST

ACTION

APPLICABILITY

1

NOTE: The ECM must have proper power and ground connections for the
following tests to be valid. Refer to Checking the ECM Power and Grounds
in the symptom list.
Turn the ignition on.
With the DRBIII

t

, read the ECM DTCs.

Does the DRBIII

t

display any ECM DTCs?

All

Yes

→

Refer to symptom list for problems related to ECM DTC.
Perform NO START VERIFICATION - VER-1.

No

→

Go To

2

2

Turn the ignition on.
With the DRBIII

t

, read the SKIM DTCs.

Does the DRBIII

t

display any SKIM DTCs?

All

Yes

→

Refer to symptom list for problems related to SKIM DTC.
Perform NO START VERIFICATION - VER-1.

No

→

Go To

3

234

DRIVEABILITY - DIESEL

ProCarManuals.com

Содержание Jeep Grand Cherokee 2002





























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды