manualshive.com logo in svg

DaimlerChrysler Jeep Grand Cherokee 2002, Руководство по обслуживанию

Поделиться
Скачать
DaimlerChrysler Jeep Grand Cherokee 2002 Скачать руководство пользователя страница 236

TEST

ACTION

APPLICABILITY

5

Turn the ignition on.
With the DRBIII

t

in Inputs/Outputs, read the Primary and Secondary brake switch

states while pressing and releasing the Brake Pedal several times.
Did the DRBIII

t

indicate the correct brake pedal state when pressing and releasing

the Brake Pedal?

All

Yes

→

Go To

6

No

→

Refer to symptom list for problems related to Brake Switch
Signal.
Perform SPEED CONTROL VERIFICATION - VER-4.

6

WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?

All

Yes

→

Repair as necessary.
Perform SPEED CONTROL VERIFICATION - VER-4.

No

→

Replace and program the Engine Control Module in accordance
with the Service Information.
Perform SPEED CONTROL VERIFICATION - VER-4.

228

DRIVEABILITY - DIESEL

*CHECKING THE SPEED CONTROL OPERATION —

Continued

ProCarManuals.com

Содержание Jeep Grand Cherokee 2002





























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды