manualshive.com logo in svg

DaimlerChrysler Jeep Grand Cherokee 2002, Руководство по обслуживанию

Поделиться
Скачать
DaimlerChrysler Jeep Grand Cherokee 2002 Скачать руководство пользователя страница 21

Symptom:

*NO RESPONSE FROM ECM (SCI ONLY) - DIESEL ONLY

POSSIBLE CAUSES

CHECK ECM POWERS AND GROUNDS

SCI TRANSMIT CIRCUIT SHORTED TO VOLTAGE

TRANSMISSION CONTROL MODULE

SCI TRANSMIT CIRCUIT SHORTED TO GROUND

SCI TRANSMIT CIRCUIT OPEN

ENGINE CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Perform the symptom Checking ECM Power and Ground Circuits in the Driveability
category.
Did the vehicle pass this test?

All

Yes

→

Go To

2

No

→

Repair as necessary.
Perform ROAD TEST VERIFICATION - VER-2.

2

Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the DRB from the DLC.
Measure the resistance between ground and the SCI Transmit circuit.
Is the resistance below 5.0 ohms?

All

Yes

→

Go To

3

No

→

Go To

4

3

Turn the ignition off.
Disconnect the TCM C1 harness connector.
Measure the resistance between ground and the SCI Transmit circuit.
Is the resistance below 5.0 ohms?

All

Yes

→

Repair the SCI Transmit circuit for a short to ground.
Perform ROAD TEST VERIFICATION - VER-2.

No

→

Replace the Transmission Control Module in accordance with the
service information.
Perform ROAD TEST VERIFICATION - VER-2.

4

Turn the ignition off.
Disconnect the DRB from the DLC.
Disconnect the ECM harness connectors.
Disconnect the TCM C1 harness connector.
Turn the ignition on.
Measure the voltage of the SCI Transmit circuit at the DLC connector (cav 7).
Is the voltage above 1.0 volt?

All

Yes

→

Repair the SCI Transmit circuit for a short to voltage.
Perform ROAD TEST VERIFICATION - VER-2.

No

→

Go To

5

13

COMMUNICATION

ProCarManuals.com

Содержание Jeep Grand Cherokee 2002





























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды