manualshive.com logo in svg

DaimlerChrysler Jeep Grand Cherokee 2002, Руководство по обслуживанию

Поделиться
Скачать
DaimlerChrysler Jeep Grand Cherokee 2002 Скачать руководство пользователя страница 143

Symptom:

P0641-SENSOR REFERENCE VOLTAGE A CKT VOLTAGE TOO
HIGH

When Monitored and Set Condition:

P0641-SENSOR REFERENCE VOLTAGE A CKT VOLTAGE TOO HIGH

When Monitored:

With the ignition on.

Set Condition:

The ECM detects a short to voltage on the Sensor Reference Voltage A

circuit or the Fuel Pressure Sensor 5-Volt Supply circuit.

POSSIBLE CAUSES

INTERMITTENT CONDITION

SENSOR REFERENCE VOLTAGE A SHORTED TO VOLTAGE

ENGINE CONTROL MODULE

FUEL PRESSURE SENSOR 5 VOLT SUPPLY CIRCUIT SHORTED TO VOLTAGE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, erase ECM DTCs.
Monitor the DRB for ECM DTCs.
Did this DTC set again?

All

Yes

→

Go To

2

No

→

Go To

5

2

Turn the ignition off.
Disconnect the MAF and APP Sensor harness connectors.
Disconnect the ECM harness connectors.
Remove the ASD Relay from the PDC.
Connect a jumper wire between cavity 30 and cavity 87 of the ASD Relay connector.
Turn the ignition on.
Measure the voltage on the Sensor Reference Voltage A circuit.
Is the voltage above 1.0 volt?

All

Yes

→

Repair the Sensor Reference Voltage A circuit for a short to
voltage.
Perform ROAD TEST VERIFICATION - VER-2.

No

→

Go To

3

NOTE: Remove the jumper wire and reinstall the ASD Relay.

135

DRIVEABILITY - DIESEL

ProCarManuals.com

Содержание Jeep Grand Cherokee 2002





























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды