Daikin VRV IV+ RXYTQ8U5YF Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 144

background image

9

|

Maintenance and service

Installer and user reference guide

34

RXYTQ

VRV IV+ heat pump for high ambient temperatures

4P561157-1B – 2021.11

9.2 Maintenance before a long stop period

E.g., at the end of the season.

▪

Let the indoor units run in fan only operation for about half a day in order to dry
the interior of the units. Refer to

"7.3.2 About cooling, heating, fan only, and

automatic operation"

25] for details on fan only operation.

▪

Turn off the power. The user interface display disappears.

▪

Clean air filters and casings of indoor units. Contact your installer or maintenance
person to clean air filters and casings of the indoor unit. Maintenance tips and
procedures for cleaning are provided in the installation/operation manuals of
dedicated indoor units. Make sure to install cleaned air filters back in the same
position.

9.3 About the refrigerant

This product contains fluorinated greenhouse gases. Do NOT vent gases into the
atmosphere.

Refrigerant type: R410A

Global warming potential (GWP) value: 2087.5

NOTICE

Applicable legislation on

fluorinated greenhouse gases

requires that the refrigerant

charge of the unit is indicated both in weight and CO

2

equivalent.

Formula to calculate the quantity in CO

2

equivalent tonnes:

GWP value of the

refrigerant × total refrigerant charge [in kg] / 1000

Please contact your installer for more information.

WARNING

The refrigerant in the system is safe and normally does not leak. If the refrigerant
leaks in the room, contact with a fire of a burner, a heater or a cooker may result in a
harmful gas.

Turn off any combustible heating devices, ventilate the room and contact the dealer
where you purchased the unit.

Do NOT use the system until a service person confirms that the portion where the
refrigerant leaks is repaired.

9.4 After-sales service and warranty

9.4.1 Warranty period

▪

This product includes a warranty card that was filled in by the dealer at the time
of installation. The completed card has to be checked by the customer and
stored carefully.

▪

If repairs to the product are necessary within the warranty period, contact your
dealer and keep the warranty card at hand.

«
...
32
33
34
35
36
...
»

Содержание VRV IV+ RXYTQ8U5YF

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для VRV IV+ RXYTQ8U5YF

Бренд: KDK Страницы: 40

Бренд: DAB Страницы: 64

Бренд: Daitsu Страницы: 50

Бренд: Oasis Aquatics Страницы: 14

Бренд: Jaga Страницы: 2

Бренд: Warmlite Страницы: 12

Бренд: CASELLA CEL Страницы: 27

Бренд: Inelco Страницы: 23

Бренд: Unico Страницы: 48

Бренд: EBARA Страницы: 18

Бренд: HERBORNER pumpentechnik Страницы: 39

MONOLITE 320 GT

Бренд: ICI Caldaie Страницы: 36

Бренд: Desmi Страницы: 34

Бренд: Flotec Страницы: 20

Watrod Electric Tubular Heaters

Бренд: Watlow Страницы: 2

Бренд: American Water Heater Страницы: 2

Бренд: DAYLIFF Страницы: 12

Бренд: Leister Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды