background image

Installation and Application Information

www.DaikinApplied.com 11 

IOM 1207-6 • TRAILBLAZER

®

 MODEL AGZ CHILLERS

Case 3: Three or More Units, Side-by-Side

For all models, there must be a minimum distance between 

any units placed side-by-side; however, performance may be 

affected at this distance. Minimum distances are: 

models 030 

to 070 - 4 feet, models 075 to 101 - 5 feet, models 110 to 241 

- 6 feet. 

Figure 9

 and 

Figure 10

 depict Case 3 performance 

adjustments as the distance between units increases.

NOTE: 

Data in 

Figure 9

 and 

Figure 10

 is for the middle unit 

with a unit on each side. See Case 2 adjustment 

factors for the two outside units.

Figure 8: Three or More Units, Side-by-Side  

Figure 9: Case 3 - Full Load Capacity Reduction  

Figure 10: Case 3 - Power Increase  

Case 4: Open Screening Walls 

Decorative screening walls are often used to help conceal a 

unit either on grade or on a rooftop. When possible, design 

these walls such that the combination of their open area 

and distance from the unit (see 

Figure 11

) do not require 

performance adjustment. If the wall opening percentage is less 

than recommended for the distance to the unit, it should be 

considered as a solid wall. It is assumed that the wall height is 

equal to or less than the unit height when mounted on its base 

support. If the wall height is greater than the unit height, see 

Case 5: Pit Installation for performance adjustment factors. 

The distance from the sides of the unit to the side walls must 

be sufficient for service, such as opening control panel doors. 

For uneven wall spacing, the distance from the unit to each 

wall can be averaged providing no distance is less than 4 feet. 

Values are based on walls on all four sides.

Figure 11: Case 4 - Allowable Wall Open Area  

 

0.0

1.0

2.0

3.0

4.0

5.0

6.0

4

5

6

8

%

 C

ap

ac

ity

 R

ed

uc

tio

n

Distance Between Units

Full Load Capacity Reduction

AGZ030-035E

AGZ040-070E

AGZ075-101E

AGZ0110-130E

AGZ140-180E

AGZ191-211E

AGZ226-241E

0.0

1.0

2.0

3.0

4.0

5.0

6.0

7.0

8.0

4

5

6

8

%

 P

ow

er

 In

cr

ease

Distance Between Units (ft)

Power Increase

AGZ030-035E

AGZ040-070E

AGZ075-101E

AGZ0110-130E

AGZ140-180E

AGZ191-211E

AGZ226-241E

3.0

4.0

5.0

6.0

7.0

8.0

9.0

0

10

20

30

40

50

D

is

ta

nc

fr

om

 W

al

l to

 U

ni

t (ft)

% Open Wall Area

Wall Free Area vs . Distance

AGZ030-070E

AGZ075-101E

AGZ110-130E

AGZ140-180E

AGZ191-241E

Содержание Trailblazer AGZ030E-070E





















































































































































Отзывы: