Daikin Super Multi NX FLKS25BAVMB Скачать руководство пользователя страница 126 | Manualshive

Страница: 126 / 144

Daikin Super Multi NX FLKS25BAVMB Скачать руководство пользователя страница 126

Tips for Servicing

SiBE05-722EE

116

Trial Operation and Field Settings

1.Tips for Servicing

1.1

Pump Down Operation

Outline

In order to protect the environment, be sure to conduct pump down operation when relocating or
disposing of the unit.

Detail

1) Remove the valve caps from the liquid stop valve and the gas stop valve.
2) Carry out forced cooling operation.
3) After 5 to 10 minutes, close the liquid stop valve with a hexagonal wrench.
4) After 2 to 3 minutes, close the gas stop valve and stop the forced cooling operation.

Refer to page 116 for forced cooling operation.

1.2

Forced Cooling Operation

Gas stop valve

Valve cap

Close

Liquid stop valve

Service port

(R13628)

Hexagonal
wrench

Item

Forced Cooling

Conditions

The forced cooling operation is allowed when both of the following conditions are
met.

1) The outdoor unit is not abnormal and not in the 3-minute standby mode.
2) The outdoor unit is not operating.

Start

The forced cooling operation starts when any of the following conditions is fulfilled.

1) Press the forced cooling operation

ON/OFF

button (SW1) on the indoor unit for

5 seconds.
2) Press the forced cooling operation ON/OFF button (SW1) on the outdoor unit.
(RK(X)S25/35E2V1B, RK(X)S25/35G2V1B, RK(X)S25/35G2V1B9,
RXS25/35J2V1B, RXS25K3V1B, RXS35K2V1B, RXS25/35L2V1B only)

Command
frequency

RK(X)S25/35E2V1B, RK(X)S25/35G2V1B: 68 Hz
RK(X)S25/35G2V1B9, RXS25/35J2V1B, RXS25K3V1B, RXS35K2V1B,
RXS25/35L2V1B: 58 Hz

End

The forced cooling operation ends when any of the following conditions is fulfilled.

1) The operation ends automatically after 15 minutes.
2) Press the forced cooling operation

ON/OFF

button (SW1) on the indoor unit

again.
3) Press the

ON/OFF

button on the remote controller.

4) Press the forced cooling operation ON/OFF button (SW1) on the outdoor unit.
(RK(X)S25/35E2V1B, RK(X)S25/35G2V1B, RK(X)S25/35G2V1B9,
RXS25/35J2V1B, RXS25K3V1B, RXS35K2V1B, RXS25/35L2V1B only)

Others

Protection functions have priority over all other functions during forced cooling
operation.

«
...
124
125
126
127
128
...
»

Содержание Super Multi NX FLKS25BAVMB

















































































































































Отзывы:

Нет отзывов