Daikin Rotex A1 BO 15-e Скачать руководство пользователя страница 22

Страница: 22 / 60

FA ROTEX A1 BOe - 02/2014

Start-up

5.2

Checklists for start-up

Checklist before start-up

Is the ROTEX A1 BO correctly set up according to an admissible set up variant and without visible damages?

yes

When using a pressure assembly: Is the installation site additionally secured (leakproof tray, filter cup of metal)?

yes

Combustion air supply secured?

yes

Adequate ventilation and extraction in the heating room with limited room-air independent (separate flue
gas/intake air) or room-air dependent operation?

yes

Does the mains connection conform to the specifications?

yes

Is the mains voltage 230 V, 50 Hz?

yes

Flue gas line connected correctly with a consistent gradient (at least 3°) and no leaks?

yes

Condensate box correctly connected, filled with water and leakproof?

yes

On restoration: Heat distribution network flushed out? Sludge separator fitted in heating return?

yes

10. Is the diaphragm expansion tank mounted according to specifications and of the requisite size?

yes

11. Is the safety valve connected to a safe free drain?

yes

12. Has the quality of the filling water been checked and has any necessary water preparation been carried out?

yes

13. System water pressure within prescribed range?

yes

14. Are boiler and heating system vented?

yes

15. In case of systems with a hot water storage tank:

a) Storage tank filled?

yes

b) Is the 3-way diverter valve correctly mounted on the flow connection and PCB plug inserted?

yes

16. Are all sensors connected and correctly positioned?

yes

17. Mixer group, mixer module and mixer circuit sensor (optional) connected correctly?

yes

18. Room controller (optional) correctly connected to the PCB?

yes

19. Oil connection connected correctly and properly in accordance with regulations and checked for leaks?

yes

20. Oil tank adequately filled and oil valves opened?

yes

The system may only be started up if all questions can be answered with "Yes".

Checklist after start-up

Is the heating circulation pump running? Is the heater heating up?

yes

Is the oil line vented?

yes

Is the oil pressure within the permissible range?

yes

Have the burner settings been checked by using a flue gas analyser and readjusted if necessary?

yes

Has the resistance of the flue gas pipe been measured and if so, is the measured resistance higher than the re-
quired minimum resistance?

yes

In case of systems with a hot water storage tank: Has the 3-way diverter valve connector been plugged on fol-
lowing start-up?

yes

The system may only be handed over to the user/owner if all questions can be answered with "Yes".

Fill out the enclosed installation and instruction form as well as the first pages of the operating manual together with the.

Содержание Rotex A1 BO 15-e





























































Результаты поиска

Содержание Rotex A1 BO 15-e

Отзывы:

Похожие инструкции для Rotex A1 BO 15-e

Бренды по названию

Популярные бренды

Daikin Rotex A1 BO 15-e, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Rotex A1 BO 15-e

Отзывы:

Похожие инструкции для Rotex A1 BO 15-e

Бренды по названию

Популярные бренды