Daikin RMKS112EV1A страница 4 Скачать руководство пользователя

Страница: 4 / 32

Outdoor Unit

Si181095

Removal Procedure

1. Outdoor Unit

1.1

Removal of Outer Panels

Procedure

Warning

Be sure to wait for 10 minutes or more after turning off all power
supplies before disassembling work.

Step

Procedure

Points

Remove the 8 screws
and remove the top
panel.

Remove the screw of
the front panel (2).
Push the front panel (2)
downward to release
the hook and remove it.

Remove the screw and
remove the piping cover
(front).

Remove the 4 screws
and remove the piping
cover (rear).

Detach the outdoor
temperature thermistor.
Remove the 6 screws
and remove the right
side panel.

It is possible to remove only
the front panel (2) without
removing the top panel.

Top panel

(R12962)

Front panel
(2)

Piping cover
(front)

Hook

(R12963)

Right side
panel

Piping cover
(rear)

(R9211)

Outdoor temperature
thermistor

Содержание RMKS112EV1A

































Результаты поиска

Содержание RMKS112EV1A

Отзывы:

Похожие инструкции для RMKS112EV1A

Бренды по названию

Популярные бренды

Daikin RMKS112EV1A, Руководство по обслуживанию

Результаты поиска

Содержание RMKS112EV1A

Отзывы:

Похожие инструкции для RMKS112EV1A

Бренды по названию

Популярные бренды