Daikin MicroTech III Скачать руководство пользователя страница 57

Страница: 57 / 68

ffeCTIve

CCupanCy

odes

www.DaikinApplied.com 57

ED 15103-6 • MICROTECH III WSHP UNIT CONTROLLER

ffeCTIve

CCupanCy

odes

This section describes the relationship among the three

network occupancy inputs that determine the resulting effective

occupancy of the unit. Refer to

orks

networks.

Table 27: Effective Occupancy Mode - BACnet

Local Sensor

Occupancy

Override

Input (MSV7)

Range: 1-5

Occupancy

Scheduler

Input (MSV8)

Range: 1–4

Occupancy

Sensor Input

(MSV9)

Range: 1–3

Effective

Occupancy

Output

(MSV6)

Range: 1–5

1 (Occ)

2 (Unoc)

3 (Bypass)

1 (Occ)

2 (Unoc)

3 (Bypass)

3 (Standby)

3 (Bypass)

4 (Null)

1 (Occ)

2 (Unoc)

4 (Standby)

5 (Null)

1 (Occ)

2 (Unoc)

4 (Standby)

2 (Unoc)

3 (Standby)

4 (Standby)

4 (Null)

1 (Occ)

2 (Unoc)

Occ

5 (Null)

4 (Null)

3 (Null)

1 (Occ)

Unoc

5 (Null)

4 (Null)

3 (Null)

2 (Unoc)

Note: Refer to

BACnet Network Objects

for full BACnet name and descriptions.

Table 28: Effective Occupancy Mode -

orks

Local

Sensor

nviOccManCmd nviOccSchedule

nviOccSensor

nvoEffectOccup

OC_OCCUPIED

OC_

UNOCCUPIED

OC_

UNOCCUPIED

OC_BYPASS

OC_OCCUPIED

OC_

UNOCCUPIED

OC_BYPASS

OC_STANDBY

OC_BYPASS

OC_NUL

OC_OCCUPIED

OC_

UNOCCUPIED

OC_

UNOCCUPIED

OC_STANDBY

OC_NUL

OC_OCCUPIED

OC_

UNOCCUPIED

OC_STANDBY

OC_

UNOCCUPIED

OC_

UNOCCUPIED

OC_STANDBY

OC_NUL

OC_OCCUPIED

OC_

UNOCCUPIED

OC_

UNOCCUPIED

OCC

OC_NUL

OC_OCCUPIED

UNOCC

OC_NUL

OC_

UNOCCUPIED

Notes:

1. OC_BYPASS can be initiated by either nviOccManCmd or a local input.

nvoEffectOccup will only be OC_BYPASS for the duration of the Local Bypass Time

(nciBypassTime), until reinitiated by either a transition of the local input or an update to

nviOccManCmd.
2. The occupancy sensor can be either a local input or a network input. If a valid value

for the network input is present, it has precedence over a local input.
3. For the occupancy sensor, OC_NUL (and no local input) is interpreted as OC_

OCCUPIED.

4. For nviOccSchedule, this refers to the “current state” field.

5. “Any State” = Any State.

Содержание MicroTech III





































































Результаты поиска

Содержание MicroTech III

Отзывы:

Похожие инструкции для MicroTech III

Бренды по названию

Популярные бренды

Daikin MicroTech III, Лист данных по продажам и инженерии

Результаты поиска

Содержание MicroTech III

Отзывы:

Похожие инструкции для MicroTech III

Бренды по названию

Популярные бренды