Daikin Magnitude WME Series Скачать руководство пользователя страница 16

Страница: 16 / 60

IOM 1266-2 • MAGNITUDE

MODEL WME CHILLERS

16 www.DaikinApplied.com

nsTallaTIon

Compressor Rigging Requirements

To properly rig the compressor, install swivel lifting eye-bolts

in the two holes on the top of the compressor (see

Figure 15,

flag #9). Use a spreader bar between the two chain hoists,

as shown in

Figure 13

, to safely lift the compressor. Note

compressor weights and dimensions in

Table 5

and

unit rigging

instructions in

Figure 5 on page 8

Figure 13: WME Compressor Rigging Setup

NOTE:

The spreader bar in

Figure 13

is a representation

only and may not reflect the appearance of the actual

spreader bar needed.

Compressor Removal and

Re-Attachment Instructions

Follow the steps listed to remove and re-attach the

compressor.

Compressor Removal Preparation

1.  Close shut-off king valve at condenser liquid line outlet.
2.  Close all other related shut-off valves.
3.  Pump the refrigerant charge down into the condenser.
4.  Ensure that the charge has been removed from the

compressor and evaporator and that the discharge check

valve is holding the charge in the condenser.

5. Loosen and remove bolts on the top side of the

compressor discharge nozzle (see

Figure 14

, flag #5).

Loosen and remove bolts at flange on condenser and

remove discharge piping.

7. Cover openings to prevent foreign objects entering.

WARNING

Improper rigging, lifting, or moving of a unit can result in

property damage, severe personal injury or death. Follow

rigging and moving instructions carefully.

Figure 14: Compressor Removal Preparation

Compressor Removal

1. Loosen and remove bolts/screws on either side of the

cast suction elbow (see

Figure 15

, flag #1).

Figure 15: Compressor Removal/Re-Attachment

2. Remove rotor cooling return line on the underside of the

compressor motor housing along with both rotor cooling

supply lines.

3. Remove (2) DIN connectors from the solenoid coils along

refrigerant piping.

4. Remove rotor stepping valve control wire. The wire ties

will have to be cut away during this process.

335652806

TYP

4 PLACES

335652807

Содержание Magnitude WME Series





























































Результаты поиска

Содержание Magnitude WME Series

Отзывы:

Похожие инструкции для Magnitude WME Series

Бренды по названию

Популярные бренды

Daikin Magnitude WME Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Magnitude WME Series

Отзывы:

Похожие инструкции для Magnitude WME Series

Бренды по названию

Популярные бренды