Daikin Intelligent Touch Manager DCM601A71 Скачать руководство пользователя страница 193

Страница: 193 / 309

User’s Manual EM11A017

DCM601A71 intelligent Touch Manager

192

8-4 Setting up the Temperature Limit

Temperature Limit is a function that keeps the room temperature within an upper and lower limits by

automatically starting the cooling or heating when the room temperature exceeds the set upper

limit or drops below the set lower limit. Using this function, you can prevent condensation and

overheating in products stored in an unmanned room.

This function performs the following every 5 minutes for each indoor unit registered with a

Temperature Limit group you have created and have this function enabled.

•

When Off and room temperature > upper limit room temperature, sends the order to cool.

•

When Off and room temperature < lower limit room temperature, sends the order to heat.

•

When cooling is On by this function and room temperature < upper limit temperature –7°F, or

room temperature < cool setpoint, sends the order to stop.

•

When heating is On by this function and room temperature > lower limit room tempe7°F,

or room temperature > heat setpoint, sends the order to stop.

•

Assessments following an order to start cooling or heating are not performed until after a

period of 30 minutes. However, assessments are performed immediately and then, every

5 minutes when they follow a group member or group attribute change.

NOTE

Room temperature

Time

Lower limit

Upper limit

<Room Temperature and Operation>

Heat ON

Lower limit +7°F

Upper limit –7°F

Heat OFF

Cool ON

Cool OFF

Heating

Cooling

Room
temperature
kept within
this range

However, in the following situations, the above is not performed:

•

The indoor unit is On by an order from another function, such as the Schedule Control or

Interlocking Control function.

•

The indoor unit received an order to start from another function while in operation by an order

from this function.

•

The suction temperature for the indoor unit cannot be acquired.

•

Be careful since an indoor unit that has been started by this function will remain On if the

suction temperature cannot be acquired.

NOTE

Содержание Intelligent Touch Manager DCM601A71






















































































































































































































































































































Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды

Daikin Intelligent Touch Manager DCM601A71, Руководство пользователя

Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды