manualshive.com logo in svg

Daikin FXZQ05TBVJU, Руководство по установке, Страница: 15 / 16

Поделиться
Скачать
Daikin FXZQ05TBVJU Скачать руководство пользователя страница 15

10

English

For remote control (force off or on / off operation)

1 

Wiring method and specification

• 

Remote control is available by connecting the external input to 

the terminal T1 and T2 on the terminal block for transmission 
wiring.

F2 T1 T2

Input A

Wiring  

specification

Sheathed vinyl cord 
or 2 core cable

Gauge

AWG18-16
(0.75 – 1.25 mm

2

)

Wiring length

Max. 328 ft. 

 

(100 m)

External 

 

contact spec

Contact that can 
make and break  
the min. load of  
15 V DC , 1 mA

2 

Actuation
•  Input A of FORCED OFF and ON/OFF OPERATION will be as 

the table shown below.

Input A = ON

Input A = OFF

In case of FORCED 
OFF

Remote controller 

prohibited

Remote controller 

permitted

In case of ON/OFF 
OPERATION

Operation

Stop

3 

How to choose FORCED OFF or ON/OFF OPERATION
•  For choosing FORCED OFF or ON/OFF OPERATION, setting by 

remote controller is required. 

[1] Enter into the field setting mode with the remote controller.

 

[2] Select Mode No. 12. 
[3] Set the First code No. to 1. 
[4-1] For FORCED OFF, set the Second code No. to 01. 
[4-2]  For ON/OFF OPERATION, set the Second code No. to 02.
(It is set to FORCED OFF when shipped from the factory.)

Test operation

Refer to the installation manual of the outdoor unit.

NOTE

When performing field settings or test operation, 

always attach the decoration panel. Otherwise, this 
may cause condensation.

The operation lamp of the remote controller will flash when an error 

occurs. Check the error code on the display to identify the trouble. 
Refer to the installation manual attached to the outdoor unit or contact 
your dealer.

•  Check the operation of the horizontal blade during test operation.

 CAUTION

After the test operation is completed, check the items mentioned in 

“For the following items, take special care during construction 

and check after installation is finished”

 on page 2.

If the interior finish work is not completed when the test operation is 
finished, for protection of the air conditioner, ask the customer not 
operate the air conditioner until the interior finish work is completed.

If the air conditioner is operated, the inside of the indoor units may 
be polluted by substances generated from the coating and 

adhesives used for the interior finish work and cause water splash 

and leakage.

 To the operator carrying out test operation

After test operation is completed, before delivering the air 

conditioner to the customer, confirm that the control box cover is 

closed.

In addition, explain the power supply status (power supply ON/

OFF) to the customer.

01_EN_3P493125-3C.indd   10

2021/12/09   11:43:31

Содержание FXZQ05TBVJU

















Отзывы:

Нет отзывов