background image

7

English

Installation of indoor unit

Step one: choosing installation location

Recommend the installation location to the client and then confirm it with the client.

Step two: install wall-mounting frame

1. Hang the wall-mounting frame on the wall; adjust it in horizontal position with the 

level meter and then point out the screws fixing holes on the wall.

2. Drill the screw fixing holes on the wall with impact drill (the specification of drill 

head should be the same as the plastic expansion particle) and then fill the plastic 

expansion particles in the holes.

3. Fix the wall-mounting frame on the wall with tapping screws (ST4.2X25TA) and 

then check if the frame is firmly installed by pulling the frame. If the plastic 

expansion particle is loose, please drill another fixing hole nearby.

Step three: open piping hole

1. Choose the position of piping hole according to the direction of outlet pipe. 

The position of piping hole should be a little lower than the wall-mounted frame, 

shown as below.

2. Open a piping hole with the diameter of Ø55 or Ø70 on the selected outlet pipe 

position. In order to drain smoothly, slant the piping hole on the wall slightly 

downward to the outdoor side with the gradient of 5-10°.

ø55

ø55

Left

Wall

Right

Mark in the middle of it

Level meter

Wall

Space 

to the 

wall 

above 

150mm

(Rear piping hole) 

(Rear piping hole) 

Space 

to the 

wall 

above 

150mm

20 and 25 class:

Left

Wall

Right

Mark in the middle of it

Level meter

Wall

Space 

to the 

wall 

above 

150mm

(Rear piping hole) 

(Rear piping hole) 

Space 

to the 

wall 

above 

150mm

ø55mm or ø70mm

Fig.5

ø55mm or ø70mm

35 class:

Left

Wall

Right

Mark in the middle of it

Level meter

Wall

Space 

to the 

wall 

above 

150mm

(Rear piping hole) 

(Rear piping hole) 

Space 

to the 

wall 

above 

150mm

ø70mm

ø70mm

60 class:

Left

Wall

Right

Mark in the middle of it

Level meter

Wall

Space 

to the 

wall 

above 

150mm

(Rear piping hole) 

(Rear piping hole) 

Space 

to the 

wall 

above 

150mm

ø55mm

ø55mm

50 class:

Содержание FTYNV20AV1









































Отзывы: