background image

English

1-5

Remote controller (wireless kit) transmitting distance can be 
shorter than expected in rooms with electronic fluorescent 
lamps (inverter or rapid start types). Install the indoor unit 
far away from fluorescent lamps as much as possible.
Indoor units are for indoor installation only. Outdoor units 
can be installed either outdoors or indoors. This unit is for 
indoor use.
Do not install the air conditioner or heat pump in the 
following locations:
(a)  

Where a mineral oil mist or oil spray or vapor is 
produced, for example, in a kitchen. Plastic parts may 
deteriorate and fall off or result in water leakage.

(b)  

Where corrosive gas, such as sulfurous acid gas, is 
produced. Corroding copper pipes or soldered parts 
may result in refrigerant leakage.

(c)  

Near machinery emitting electromagnetic waves. 
Electromagnetic waves may disturb the operation of 
the control system and cause the unit to malfunction.

(d)   Where flammable gas may leak, where there is carbon 

fiber, or ignitable dust suspension in the air, or where 
volatile flammables such as thinner or gasoline are 
handled. Operating the unit in such conditions can cause 
a fire.

Take adequate measures to prevent the outdoor unit from 
being used as a shelter by small animals. Small animals 
making contact with electrical parts can cause malfunctions, 
smoke, or fire. Instruct the user to keep the area around the 
unit clean.

!

 DANGER

Refrigerant gas is heavier than air and replaces oxygen. A 
massive leak can lead to oxygen depletion, especially in 
basements, and an asphyxiation hazard could occur leading 
to serious injury or death.
Do not ground units to water pipes, gas pipes, telephone 
wires, or lightning rods as incomplete grounding can cause 
a severe shock hazard resulting in severe injury or death. 
Additionally, grounding to gas pipes could cause a gas leak 
and potential explosion causing severe injury or death.
If refrigerant gas leaks during installation, ventilate the 
area immediately. Refrigerant gas may produce toxic gas if 
it comes into contact with fire. Exposure to this gas could 
cause severe injury or death.
After completing the installation work, check that the 
refrigerant gas does not leak throughout the system.
Do not install unit in an area where flammable materials 
are present due to risk of explosions that can cause serious 
injury or death.
Safely dispose all packing and transportation materials 
in accordance with federal/state/local laws or ordinances. 
Packing materials such as nails and other metal or wood parts, 
including plastic packing materials used for transportation 
may cause injuries or death by suffocation.

!

 NOTE

Install the power supply and inter-unit wires for the indoor 
and outdoor units at least 3.5ft away from televisions or 
radios to prevent image interference or noise. Depending 
on the radio waves, a distance of 3.5ft may not be sufficient 
to eliminate the noise.
Dismantling the unit, treatment of the refrigerant, oil and 
additional parts must be done in accordance with the relevant 
local, state, and national regulations.
Do not use the following tools that are used with conventional 
refrigerants: gauge manifold, charge hose, gas leak detector, 
reverse flow check valve, refrigerant charge base, vacuum 
gauge, or refrigerant recovery equipment.
If the conventional refrigerant and refrigerator oil are mixed 
in R410A, the refrigerant may deteriorate.
This air conditioner or heat pump is an appliance that should 
not be accessible to the general public.
As design pressure is 536 psi, the wall thickness field-
installed pipes should be selected in accordance with the 
relevant local, state, and national regulations.

NOTICE 

Disposal requirements

Your air conditioning product is marked with this symbol. This means that electrical and electronic products shall not be mixed with 
unsorted household waste.
Do not try to dismantle the system yourself: the dismantling of the air conditioning system, treatment of the refrigerant, of oil and of 
other parts must be done by a quali

fi

 ed installer in accordance with relevant local and national legislation.

Air conditioners must be treated at a specialized treatment facility for re-use, recycling and recovery. By ensuring this product is 
disposed of correctly, you will help to prevent potential negative consequences for the environment and human health. Please contact 
the installer or local authority for more information.
Batteries must be removed from the remote controller and disposed of separately in accordance with relevant local and national 
legislation.

1 IM-5WMYJ(R)-0617(0)-DAIKIN USA5   5

1 IM-5WMYJ(R)-0617(0)-DAIKIN USA5   5

10/12/17   10:30:59 AM

10/12/17   10:30:59 AM

Содержание FTXB12A

































































Отзывы: