Daikin EWWD320DZXSA1 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 32

Daikin EWWD320DZXSA1 Скачать руководство пользователя страница 14

D-EIMWC01405-18EN- 14/32

2.9

Temperature limits and water flow

EWWD(H) DZ units are designed to operate with an evaporate outlet water temperature between 4°C and +20°C and a
condenser outlet water temperature between 20°C and 50°C. However, the minimum temperature difference between the
evaporator outlet water temperature and the condenser inlet water temperature must not be less than 15° C. Always check
the exact operating point with the selection software. Some simultaneous operating conditions (high evaporator inlet water
temperature and high condenser inlet water temperature) may be inhibited. The maximum permissible water temperature
in  the  evaporator  with  the  machine  off  is  50°  C.  Higher  temperatures  could  cause  the  safety  valves  on  the  evaporator
sleeve to open.  Water flow rate in the condenser and evaporator under the rated value indicated in the unit selection point
can cause freezing problems, scale and poor control. Water flow rate in the condenser and evaporator higher than the
rated  value  indicated in  the  unit  selection  point  results  in  an  unacceptable  pressure  drop  and  excessive  erosion of  the
pipes and vibrations that can cause breakage.

EWWD(H)-DZ DRY COOLER VERSION

Dry cooler version Model

EWWD320DZXSA1

EWWH230DZXSA1

EWWD340DZXEA1

EWWH245DZXEA1

EWWD440DZXSA1

EWWH320DZXSA1

EWWD470DZXEA1

EWWH345DZXEA1

EWWD610DZXSA2

EWWH430DZXSA2

EWWD640DZXSA2

EWWH455DZXSA2

EWWD670DZXEA2

EWWH470DZXEA2

EWWD680DZXEA2

EWWH490DZXEA2

EWWD880DZXSA2

EWWH640DZXSA2

EWWD950DZXEA2

EWWH685DZXEA2

EWWD(H)-DZ COOLING TOWER VERSION

Cooling tower version Model

EWWD530DZXSA1

EWWH380DZXSA1

EWWD570DZXEA1

EWWH405DZXEA1

EWWD700DZXSA1

EWWH460DZXSA1

EWWD740DZXEA1

EWWH480DZXEA1

EWWDC10DZXSA2

EWWH755DZXSA2

EWWDC11DZXEA2

EWWH810DZXEA2

EWWDC14DZXSA2

EWWH920DZXSA2

EWWDC15DZXEA2

EWWH955DZXEA2

Legend:

ELWT

Evaporator outlet water temperature

CLWT Condenser outlet water temperature

2.10 Minimum water content in the system

For correct machine operations and the necessary operating stability, it is important to ensure a minimum water content in
the system. An accumulation tank with suitable volume may be required for this purpose.
The minimum water content must be calculated by considering the following specifications:

«
...
12
13
14
15
16
...
»

Содержание EWWD320DZXSA1

































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды