Daikin EWAP 800-C18AJYNN Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 40

Daikin EWAP 800-C18AJYNN Скачать руководство пользователя страница 37

D - KIMAC00512-09EN - 37/40

Troubleshooting chart

PROBLEM

POSSIBLE CAUSES

POSSIBLE CORRECTIVE STEPS

Compressor will
not run

1.  Main power switch open.
2.  Unit system switch open.

3.  Circuit switch in pump-down position.

4.  Evaporator flow switch not closed.

5.  Circuit breakers open.
6.  Fuse blown or circuit breakers tripped.

7.  Unit phase voltage monitor not satisfied.

8.  Compressor overload tripped.

9.  Defective compressor contactor or

contactor coil.

10.  System shut down by safety devices.

11.  No cooling required.

12.  Motor electrical trouble.
13.  Loose wiring.

1. Close switch.
2. Check unit status on Control Panel. Close

switch.

3. Check circuit status on Control Panel.

Close switch.

4. Check unit status on Control Panel. Close

switch.

5. Close circuit breakers.
6. Check electrical circuits and motor

windings for shorts or grounds.

Investigate for possible overloading.

Check for loose or corroded connections.

Reset breakers or replace fuses after fault
is corrected.

7. Check unit power wiring to unit for correct

phasing. Check voltage.

8. Overloads are manual reset. Reset

overload at button on overload.

Clear alarm on Microprocessor.

9. Check wiring. Repair or replace contactor.

10. Determine type and cause of shutdown

and correct problem before attempting to
restart.

11. Check control settings. Wait until unit calls

for cooling.

12. See 6, 7, 8 above.
13. Check circuits for voltage at required

points. Tighten all power wiring terminals.

Compressor
Overload Relay
Tripped or
Circuit Breaker
Trip or Fuses
Blown

1.  Low voltage during high load condition.

2.  Loose power wiring.
3.  Power line fault causing unbalanced

voltage.

4. Defective or grounded wiring in the motor.
5. High discharge pressure.

1. Check supply voltage for excessive

voltage drop.

2.  Check and tighten all connections.
3.  Check supply voltage.

4.  Check motor and Replace if defective.
5.  See Corrective steps for high discharge

pressure.

Compressor
noisy or
vibrating

1. Compressor internal problem.
2. Oil injection not adequate.

1. Contact DAIKIN.
2. Contact DAIKIN.

Compressor will
not load or
unload

1.  Defective capacity control.
2.  Unloader mechanism defective.
3.  Control solenoids defective.

1.  See capacity control section.
2.  Replace.
3.  Replace.

«
...
35
36
37
38
39
...
»

Содержание EWAP 800-C18AJYNN









































Отзывы:

Нет отзывов